Chamberlain HDSW24UL Скачать руководство пользователя | Manualshive

Страница: 16 / 64

background image

16

To prevent SERIOUS INJURY or DEATH from a moving gate:

• ALL gate operator systems REQUIRE two independent entrapment

protection systems for each entrapment zone.

• Entrapment protection devices MUST be installed to protect anyone

who may come near a moving gate.

• Entrapment protection devices MUST be located to protect in BOTH

the open and close gate cycles.

• Locate entrapment protection devices to protect between moving gate

and RIGID objects, such as posts, walls, pillars, columns, or operator
itself.

Step 6 Install Entrapment Protection

Install entrapment protection devices according to the

UL 325

Entrapment Protection Requirements

section, see

. Use the

Site

Planning Safety Checklist

in the appendix, to identify entrapment zones

that will result from the installation.

1. Install entrapment protection devices for ALL entrapment zones. This

operator has an inherent entrapment protection device built-in. The
installer MUST provide one additional entrapment protection device
for each entrapment zone.

2. The operator will NOT run unless a

minimum of one

external device

is connected in either the open or closed direction. If no entrapment
zone exists in the other direction, an external entrapment protection
device is NOT required in that direction.

3. Test ALL entrapment protection devices AFTER installing the

operator, refer to the manual provided with your entrapment
protection device.

Illustration is for example only; your site may have additional entrapment
zones which MUST be protected.

Definitions

ENTRAPMENT:

The condition when a person is caught or held in a

position that increases the risk of injury.

SWING GATE ENTRAPMENT ZONE:

Locations between a moving gate or

moving, exposed operator components and a counter opposing edge or
surface where entrapment is possible up to 1.8 m (6 ft) above grade. Such
locations occur if during any point in travel:

a. The gap between the bottom of a moving gate and the ground is

greater than 101.6 mm (4 in) and less than 406 mm (16 in); or

b. The distance between the center line of the pivot and the end of the

wall, pillar, or column to which it is mounted when in the open or
closed position exceeds 101.6 mm (4 in). Any other gap between a
moving gate and fixed counter opposing edges or surfaces or other
fixed objects is less than 406 mm (16 in) (examples are walls, curbs,
berms or other immovable objects).

See

Accessories

for approved entrapment protection devices.

Cross Section

Pedestrian gate located near
the swing gate. Make sure a
separate pedestrian entrance
is available and the path is
clearly designated.

Secure Side

Public Side

Edge

sensor

Entrapment
zone

Curb

Curb

Reflector for
photoelectric
sensor

Photoelectric
sensor

Photoelectric sensor
(public side)

Photoelectric sensor
(public side)

Earth ground

Mount access control devices at
least 6' (1.8 m) beyond the gate

Place the warning signs on both
sides of the gate in clear view

EN

TR

AP

ME

NT

ZO

NE

Take a photograph of the complete

installation site for your records

Illustrations provided by DASMA Gate Systems Safety Guide

INSTALLATION

«
...
14
15
16
17
18
...
»

Содержание HDSW24UL

































































Отзывы:

Нет отзывов

Похожие инструкции для HDSW24UL

Бренд: CAME Страницы: 2

Бренд: V2 ELETTRONICA Страницы: 42

Бренд: Gocontrol Страницы: 2

LiftMaster 3575

Бренд: Chamberlain Страницы: 36

Бренд: Bandini Industrie Страницы: 2

Бренд: Garaga Страницы: 36

Бренд: Xtreme Garage Страницы: 28

Бренд: Delton Страницы: 8

Бренд: Roma Страницы: 36

Бренд: Chamberlain Страницы: 40

Бренд: Rosle Страницы: 32

Бренд: B&D Страницы: 27

Бренд: cedamatic Страницы: 24

Бренд: tau Страницы: 44

Бренд: Palfinger Страницы: 6

Бренд: Chamberlain Страницы: 48

Бренд: GDS Страницы: 19

Бренд: Chamberlain Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды