Chamberlain HDSW24UL Скачать руководство пользователя

Страница: 22 / 64

Step 10 Dual Gate setup

There are two options for dual gate communication: wired or wireless. Follow the directions according to your application. Do not use wired and
wireless communication simultaneously.

Wired dual gate applications will have a longer battery standby time than wireless applications.

Wireless setup

To activate the wireless feature:

1. Choose an operator to be the network primary operator. All wireless accessories will need to be programmed to the primary operator.

NOTE:

recommend that all accessories and board configurations are set on the primary operator.

2. Press and release the LEARN button on the primary operator. The green XMITTER LED will light.

NOTE:

The operator will time out of programming

mode after 180 seconds.

3. Press and release the LEARN button again on the primary operator. The yellow NETWORK LED will light.

4. Press and release the OPEN test button to assign this operator as network primary.

5. Press and release the LEARN button on the second operator. The green XMITTER LED will light.

6. Press and release the LEARN button again on the second operator. The yellow NETWORK LED will light.

7. Press and release the CLOSE test button to assign this operator as network second.

Both operators will beep and the yellow NETWORK LEDs will turn off indicating programming is successful.

To deactivate the wireless feature:

1. Press and release the LEARN button on either operator. The green XMITTER LED will light.

2. Press and release the LEARN button again on the same operator. The yellow NETWORK LED will light.

3. Press and hold the LEARN button for 5 seconds. The yellow NETWORK LED will blink (operator will beep) then turn off indicating successful

deactivation.

4. Press and release SET OPEN and SET CLOSE buttons simultaneously. The yellow SET OPEN and SET CLOSE LEDs will light.

5. Press and release SET OPEN and SET CLOSE buttons simultaneously again. Both yellow LEDs will turn off and entrapment protection devices will be

relearned.

6. Repeat the steps for the other operator.

tsid

Pro

per

Ins

ide

erty

INSTALLATION

Содержание HDSW24UL

































































Результаты поиска

Содержание HDSW24UL

Отзывы:

Похожие инструкции для HDSW24UL

Бренды по названию

Популярные бренды

Chamberlain HDSW24UL, Руководство по установке

Результаты поиска

Содержание HDSW24UL

Отзывы:

Похожие инструкции для HDSW24UL

Бренды по названию

Популярные бренды