Chamberlain HDSW24UL Скачать руководство пользователя | Manualshive

Страница: 9 / 64

background image

9

Site Preparation

Check the national and local building codes

BEFORE

installation. Refer also to the

Site Planning Safety Checklist

in the Appendix.

Gate

Gate must be constructed and installed according to ASTM F2200
standards (refer to page 4). Gate must fit specifications of operator (refer
to specifications).

Inside Property

Conduit and Concrete Pad

Trench and install conduit. Before trenching, contact underground utility
locating companies. Conduit must be UL approved for low and high
voltage. Consider the operator placement BEFORE installing the pad or
post.

Concrete Pads

Inside Property

Safety

Entrapment protection devices are required to protect against any
entrapment or safety conditions encountered in your gate application.
Install a warning sign (two provided) on the inside and outside of the
property, where easily visible.

Entrapment Danger

Inside Property

Warning Signs

Additional Accessories

The vehicle loops allow the gate to stay open when vehicles are
obstructing the gate path. Suggested for vehicles 14 feet (4.27 m) or
longer. Vehicle loops are not required but are recommended. Before
installing your Access Control Device(s) be sure to complete a site survey
and determine the best device for your site needs.

Access Control
Device

Outside Property

Vehicle Loops

Check your gate

Gate MUST be level. Gate and gate
post MUST be plumb. Gate MUST
have a smooth bottom edge, no
protrusions should exist.

Remove ANY/ALL wheels from the
bottom of gate.

Gate MUST NOT hit or drag across
ground

Gate MUST swing freely and be
supported entirely by its hinges.

INTRODUCTION

«
...
7
8
9
10
11
...
»

Содержание HDSW24UL

































































Отзывы:

Нет отзывов

Похожие инструкции для HDSW24UL

Бренд: O&O Страницы: 28

Бренд: U-Line Страницы: 21

Бренд: Nice Страницы: 112

Бренд: Byan System Страницы: 30

Бренд: V2 Страницы: 48

Бренд: Dea Страницы: 44

Бренд: Dea Страницы: 48

Бренд: quiko Страницы: 2

Бренд: CAME Страницы: 2

Бренд: Wallace International Страницы: 28

Бренд: FAAC Страницы: 13

Бренд: Zero Страницы: 12

Бренд: Daspi Страницы: 35

Бренд: Raynor Страницы: 24

Бренд: Raynor Страницы: 36

Aviator II PREMIUM 8355WRGD

Бренд: Raynor Страницы: 44

Бренд: FAAC Страницы: 11

Бренд: V2 SPA Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды