Chamberlain HDSW24UL Скачать руководство пользователя | Manualshive

Страница: 21 / 64

background image

21

33AH Batteries

The batteries are charged in the circuit by the integrated transformer. The
33AH application requires battery harness K41-0102-000 (not provided)
and 33AH battery tray K41-0105-000 (not provided), see

Accessories

.

1. Turn the AC power switch to OFF.

2. Turn the battery switch OFF.

3. Connect a jumper between the po) terminal of the battery to

the negative terminal(-) of the other battery.

4. Replace the existing battery tray with 33AH battery tray. Place the

batteries in the tray.

5. Connect the (+) terminal of the battery to the red battery wire from

the operator using the RED harness kit wire .

6. Connect the (-) terminal of the battery to the black battery wire from

the operator using the BLACK harness kit wire.

7. Turn the battery switch ON .

8. Turn the AC power switch to ON to restore AC power.

33AH batteries are NOT compatible if transformer kit model 3PHCONV is
installed.

Red Wires

Black Wires

Jumper

Red and Black Wires
Harness Kit Model K42-0102-000

Battery Wiring

INSTALLATION

«
...
19
20
21
22
23
...
»

Содержание HDSW24UL

































































Отзывы:

Нет отзывов

Похожие инструкции для HDSW24UL

Бренд: Calimet Страницы: 21

Бренд: Calimet Страницы: 16

Бренд: Schlagel Страницы: 8

RADIO MOBILE TX EVO

Бренд: C.C.E. Страницы: 2

Бренд: CAME Страницы: 20

Бренд: Nice Страницы: 48

Бренд: Control-A-Door Страницы: 32

8550WRGD Admiral II

Бренд: Raynor Страницы: 44

ThermoMark 5150

Бренд: Wayne-Dalton Страницы: 4

Бренд: SOMFY Страницы: 60

Бренд: SOMFY Страницы: 52

S2500I CERNIERA

Бренд: FAAC Страницы: 12

Бренд: DITEC Страницы: 4

FIBO 300 LB-1,5 HP

Бренд: fadini Страницы: 8

Бренд: DITEC Страницы: 42

entrematic TRAFFIC C

Бренд: DITEC Страницы: 44

Бренд: CAME Страницы: 112

Бренд: Beninca Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды