Chamberlain B550 Owner'S Manual Download | Manualshive

Page: 1 / 48

background image

TO WATCH VIDEOS GO TO:

tinyurl.com/lgh5x3h

Contents

Preparation ......................................2-5
Assembly .......................................6-10
Installation ..................................11-28
Install the Door Control ............21-22
Install the Protector System® ....23-26
Connect

power

.........................27-28

Adjustments .................................29-31
MyQ® Smartphone Control .................32
Operation .....................................33-39
  Using your Garage Door Opener .....34
  To Open the Door Manually ...........34

Motion

Detecting

Control Panel ...........................35-36

Multi-Function Control Panel ....37-38
Remote

Control

.............................38

Homelink®

...................................38

To Erase the Memory .....................39
Maintenance .....................................40
Troubleshooting ...........................41-42
Accessories ........................................43
Warranty ...........................................44
Repair Parts .................................45-47

Owner’s Manual

B550 • B552 • B750

Belt Drive

Garage Door Opener

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE CONTROL

INCLUDED

www.chamberlain.com

www.mychamberlain.com

Smart Garage Opener

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL NOT CLOSE unless the Protector System

®

is connected

and properly aligned.

• Periodic checks of the garage door opener are required to ensure

safe operation.

• The model number label is located on the left side panel of your

garage door opener.

• This garage door opener is compatible with MyQ® and

S

b

2.0® accessories.

• DO NOT install on a one-piece door if using devices or features

providing unattended close. Unattended devices and features are

to be used ONLY with sectional doors.

1
2
3
...
»

Summary of Contents for B550

















































Reviews:

No comments

Related manuals for B550

Brand: Chamberlain Pages: 20

Brand: Nice Pages: 12

Brand: Pujol Pages: 16

Brand: CAME Pages: 28

Brand: ALL-O-MATIC Pages: 44

Brand: BEA Pages: 8

Brand: BEA Pages: 16

Brand: CAME Pages: 17

Brand: Seav Pages: 3

Brand: Automatic Technology Pages: 20

Brand: Wallace Perimeter Security Pages: 142

Brand: Bandini Pages: 11

Brand: vds Pages: 13

FROG PLUS Series

Brand: CAME Pages: 18

Brand: Roger Technology Pages: 4

Brand: Allmatic Pages: 16

Brand: Gatekeeper Pages: 22

Brand: Accessmatic Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands