GD00Z-7
GARAGE DOOR OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
1
PRODUCT DESCRIPTION
2
SAFETY NOTES
3
PRODUCT COMPONENTS
4
TILT SENSOR INSTALLATION AND BATTERY
5
PAIRING (INCLUDING) WITH THE SYSTEM
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-7 - P/N: 10016895 X3- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WARNING
This operator system is equipped with an unattended operation
feature. This door could move unexpectedly. NO ONE SHOULD
CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per
(UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Transceiver on garage
door operators manufactured prior to 1993 (models without an
operational safety beam entrapment detection system).
WARNING
The Remote Command Transceiver must be mounted in the
garage, in sight of the garage door, where the visual and audible
movement warning indicators can be clearly seen and heard.
GD00Z-7
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-7
POWER
SUPPLY
TILT
SENSOR
STATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00Z-7 MOUNTING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
WIRE
TIES
MOUNTING SCREW
FOR POWER SUPPLY
TO INCLUDE THE GD00Z-7
INTO YOUR CONTROLLER
1
2
WALL
OUTLET
POWER
SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
GD00Z-7
Press and release the link button
on the GD00Z-7.
Note: Plug in the GD00Z-7
near your Z-Wave Controller
for these steps
Place your Z-Wave Controller into
Discovery or Include mode.
TO EXCLUDE THE GD00Z-7
FROM YOUR CONTROLLER
Confirm that the GD00Z-7 was
recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on including devices.
3
1
2
Press and release the link button
on the GD00Z-7.
Place your Z-Wave Controller into
Exclude mode.
Confirm that the GD00Z-7 was
excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers
instructions for additional information
on excluding devices.
3
CR2032
PLUS SIDE UP !!!
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
Insert the
battery
into the
transmitter
To open the case, twist
a small screwdriver
in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST ON
BOTTOM
"UP"
ARROWS
Snap the sensor onto
the mounting plate
To activate the tilt sensor,
remove the battery protection pull strip
2
ARROWS ON PLATE
& SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate
to the
top panel of the door
GD00Z-7 Overview
• A garage door opener remote command
transceiver with built-in Z-Wave
technology.
• Allows remote operation of a garage door
opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve
communications within the Z-Wave mesh
network.
GD00Z-7 Summary of Operation
• GD00Z-7 connects to the garage door
opener’s pushbutton wall console
terminals.
• A wireless tilt sensor mounts on garage
door and reports door’s position to
GD00Z-7.
• GD00Z-7 responds to Z-Wave commands
from Z-Wave controllers to open or close
the garage door.
• A warning indicator light flashes and a
beeper sounds for 5 seconds before the
door begins to move.
• If the door does not completely open or
close, a second open or close command
can be sent after 30 seconds.
• If the door does not completely open
or close after the second attempt, the
GD00Z-7 operation is suspended until a
local garage door pushbutton is activated.
Z-Wave Information
• Z-Wave® is a registered trademark of
Sigma Designs Inc. and/or its subsidiaries.
• Z-Wave is an Interoperable two-way RF
mesh networking technology designed for
use with a Z-Wave gateway/controller and
other Z-Wave enabled devices.
• Replication is the process of copying or
transferring your Z-Wave network from one
controller to another.
• This is a Security enabled Z-Wave product
and must be used with a Security enabled
Z-Wave controller in order to fully utilize
this product. As such, this device will not
respond to Basic CC commands.
• ASSOCIATION: GD00Z-7 supports 1
Group with 1 Node. Group 1 must be
assigned the Node ID of the controller
to which unsolicited notifications from
the GD00Z-7 will be sent. The Z-Wave
controller should set this association
automatically after inclusion.
S2 Security
• New S2 security uses
Elliptic Curve
Diffie Hellman key exchange Protocol to
establish a secure communication channel.
• Uses multiple “Keys” to create a
permanent Key.
• Virtually impossible to hack.
• Z-Wave hub must also support S2
Security. If hub does not support S2,
device will operate using standard
security.
