background image

 

4. 

WORKING AND 

OPERATIONS MODES

365

UPO33

9<<

>>10

4.2.  Battery dischargue

The UPO 33 UPS works under the following operation modes:

4.1.  Normal Operation

Figure 4.1 . Operating diagram UPO 33 UPS in normal mode

Figure 4.2 Operating diagram UPO33 UPS in battery mode

Figure 3.1 shows the outline of UPO 33 UPS operation when operating normally 

In this mode, the energy delivered to the load is supplied by the battery 

bank. The investor is responsible for transforming the DC voltage into AC 

voltage batteries. The UPS enters this mode when no input voltage to the 

UPS or there is an abnormal condition at the entrance. If the abnormality to 

the input persists for a long time, the UPS will cease to supply the load in 

order to prevent a deep discharging the batteries, however, the control 

electronics and the front panel will continue to function. If the outage lasts 

much longer, it is recommended to completely turn off the UPS and discon-

nect the battery bank (see section 6.2) in order to avoid a complete dischar-

ge of the batteries.

"#$%&'!?)*)!"%,E-#+,./!<E7'=.-#E!6+&!F9!??!89:!#,!,+&=./!=+4'!

'E=J<B:;GJ)1IFD>>)

18!>K;@!BAJ?#>;B8!CB9J!>KJ!:B#9!;@!EB88JE>J9!>B!>KJ!C#;8@!>K?BD<K!#8!J:JE>?B8;E!@U;>EK!V#@J9!B8!2+)d@(!0KJ!
G42! J8>J?@! >K;@! BAJ?#>;B8! CB9J! UKJ8^! >KJ?J! U#@! @BCJ! @B?>! BF! BTJ?:B#9! #>! >KJ! BD>AD>=! >KJ?J! U#@! #!
>JCAJ?#>D?J!?;@J!#89!;>!;@!#VBTJ!>KJ!8BC;8#:!T#:DJ!BF!BAJ?#>;B8

!B?!>KJ!V#>>J?$!VJ8EK!;@!>BB!CDEK!9;@EK#?<J9(

!

+D;MDE)1IFD>>))

0KJ!G42!;@!;8!C#8D#:!V$A#@@!CB9J!UKJ8!>KJ!:B#9!;@!EB88JE>J9!9;?JE>:$!>B!>KJ!C#;8@!>K?BD<K!#!V$A#@@!E;?ED;>!
V?J#PJ?! UK;:J! >KJ! G42! ;>@J:F! ?JC#;8@! D8J8J?<;XJ9(! 0K;@! CB9J! #::BU@! >KJ! D@J?! B?! BAJ?#>B?! >B! E#??$! BD>!
C#;8>J8#8EJ!>#@P@!U;>KBD>!#E>D#::$!ED>>;8<!>KJ!ABeUJ?!>B!>KJ!:B

#9(!

'E=J<B:;GJ)1IFD>>)

18!>K;@!BAJ?#>;B8!CB9J!>KJ!:B#9!;@!EB88JE>J9!>B!>KJ!C#;8@!>K?BD<K!#8!J:JE>?B8;E!@U;>EK!V#@J9!B8!2+)d@(!0KJ!
G42! J8>J?@! >K;@! BAJ?#>;B8! CB9J! UKJ8^! >KJ?J! U#@! @BCJ! @B?>! BF! BTJ?:B#9! #>! >KJ! BD>AD>=! >KJ?J! U#@! #!
>JCAJ?#>D?J!?;@J!#89!;>!;@!#VBTJ!>KJ!8BC;8#:!T#:DJ!BF!BAJ?#>;B8

!B?!>KJ!V#>>J?$!VJ8EK!;@!>BB!CDEK!9;@EK#?<J9(

+D;MDE)1IFD>>))

0KJ!G42!;@!;8!C#8D#:!V$A#@@!CB9J!UKJ8!>KJ!:B#9!;@!EB88JE>J9!9;?JE>:$!>B!>KJ!C#;8@!>K?BD<K!#!V$A#@@!E;?ED;>!
V?J#PJ?! UK;:J! >KJ! G42! ;>@J:F! ?JC#;8@! D8J8J?<;XJ9(! 0K;@! CB9J! #::BU@! >KJ! D@J?! B?! BAJ?#>B?! >B! E#??$! BD>!
C#;8>J8#8EJ!>#@P@!U;>KBD>!#E>D#::$!ED>>;8<!>KJ!ABeUJ?!>B!>KJ!:B

#9(!

+D;MDE)!KM<H:N;)

0KJ!G42!;@!FD::$!>D?8J9!BFF!;8!>KJ!C#8D#:!@KD>9BU8!CB9J=!@B!>KJ!;8TJ?>J?!;@!>D?8J9!BFF!#89!>KJ!:B#9!K#@!8B!
ABUJ?! >K?BD<K! #8$! BF! >KJ! V$A#@@! E;?ED;>@(! -JTJ?>KJ:J@@! ;F! >KJ! V#>>J?$! VJ8EK! ;@! 9;@EK#?<J9! #89! ;8E;9J8>#::$!
>KJ?J!;@!/+!ABUJ?!#>!>KJ!;8AD>!BF!>KJ!G42=!>KJ!V#>>J?$!EK#?<J?!E;?ED;>!U;::!UB?P(!0KJ!EBCCD8;E#>;B8@!9JT;EJ@!
#89!>KJ!EB8>?B:!A#8J:!#:@B!UB?P!D89J?!>K;@!CB9J(!

!

!

"#$%&'!?)()!"%,E-#+,./!<E7'=.-#E!6+&!F9!??!89:!#,!=.,%./!5GH.<<!=+4'!

When the UPS is operating normally , the AC voltage at the input is conver-

ted into DC voltage by the rectifier .

This DC voltage is used to charge the batteries and power the inverter.

The inverter is responsible for transforming the DC voltage to the rectifier 

output in a sine wave feed the load .

Содержание UPO33



























Отзывы: