CDP UPO33 страница 24 Скачать руководство пользователя

Страница: 24 / 26

365

UPO33

45<<

>>46

10.3. Dry contact Card

10.4. Power plant operation

11. TECHNICAL SPECIFICATIONS

The relay card allows, through switches, take the signs that indicate the

status of the UPS you can use them in external devices such as mime,

PLC's or control systems. The outputs of the board indicate the status of

the UPS input, the output of UPS, batteries and inverter. For each signal is

a normally open switch and a normally closed switch, thus complementary

signals. For example when the UPS inverter is operating normally, the

normally open switch is open and normally closed switch is closed. If the

inverter fails, the normally open switch closes and the normally closed

switch will open.

With the ability to customize the UPS is easy to adapt the UPS to the

particular characteristics of virtually any power plant. The UPS CDP UPO

33 can be programmed to perform a gradual start, so that the effective

power required for emergency power plant is slightly higher than the UPS.

This energy can be up to twice the power of the UPS.

Содержание UPO33



























Результаты поиска

Содержание UPO33

Отзывы:

Похожие инструкции для UPO33

Бренды по названию

Популярные бренды

CDP UPO33, Руководство пользователя

Результаты поиска

Содержание UPO33

Отзывы:

Похожие инструкции для UPO33

Бренды по названию

Популярные бренды