Back Space + AB # + Quick Exit
Each alphabet of ABCDEFGH = 0 or 1 depending on the shorting of the Pads below the IC U2 on the PCB of
Wireless Siren PCB. On the PCB these pads are marked as 12345678.
Each Pad can either be shorted or left open.
Open pads represent “1” and shorted pads represent “0”.
Note:
At least one of the pad should be shorted.
Default value = 10111111 i.e., pad number 2 is shorted and all others are open.
So, the programming in default case would be
:
Press “SENSOR” key
Enter Master Password (1234) + # + 1
Keep Pressing 2 to select “Flashing Sir
n
”
Press #
Back Space + 10 # + Quick Exit
Note:
Wireless Flashing Sirens work with 12V DC and not 9V.
:
In one system, any number of Wireless Siren can be installed provided all of them are set in same PAD Shorting
and the main unit is programmed for that Shorting.
.
Siren Wireless or Flashing Siren-Wireless with Tamper Protection (FSW-T) Registering
.
There are following 3 parts of FSW that need to be registered with the Burglar Alarm System Main Unit
:
Registering of Flashing Siren
Press “SENSOR” key
Enter Master Password (1234) + #
Press 1
Keep Pressing 2 to select “Flashing Sir
n
”
Press #
Back Space + AB # + Quick Exit
Each alphabet of ABCDEFGH = 0 or 1 depending on the shorting of the Pads below the IC U2 on the PCB of
Wireless Siren PCB.
The 8 shorting pads represent ABCDEFGH starting from the Pad where Arrow is made.
Each Pad can either be shorted or left open.
Open pad
s represent “1” and shorted pads represent “0”.
Note:
At least one of the pad should be shorted.
Default value = 10111111 i.e., pad number 2 is shorted and all others are open.
So, the programming in default case would be:
Enter Master Password (1234) + # +
+ 03 + # + Back Space + 10 # + Quick Exit
Note:
Wireless Flashing Sirens work with 12V DC and not 9V.
:
In one system, any number of Wireless Siren can be installed provided all of them are set in same PAD Shorting
and the main unit is programmed for that Shorting.
Registering of Tamper Protection
Press “SENSOR” key
Enter Master Password (1234) + #
Press 1
Keep Pressing 2 to select “Tamper”
Press #
Dial 01 to 75 (ID number to be given to the Flashing Siren) + #
Now trigger the Wireless Circuit of the FSW (By taking away of the Magnet or by bring it close to the Wireless
Circuit)
Press #
Press “Quick Exit”
Note:
Whenever FSW is Tampered with or any of its wire is cut, the Main Unit display will show its ID number and
Zone Name as “Tamper.”
:
During the programming, the system auto cancels the operation if it doesn’t receive the input from Wireless
Sensor within 20 seconds.
Deletion of registration
To delete a FSW registration from the Main Unit:
Press “SENSOR” Key.
Enter Master Pa # + 2 + 2
Press “UP” or DOWN” to choose the ID you want to delete.
Press BACK SPACE + # + Quick Exit
Setting of Mode of Operation of FSW
Press “SENSOR” Key
Enter Master Password (1234) + # + 2 + 2
Press “UP” or DOWN” key to select the desired Wireless Sensor
Press MODE to choose any of the following modes of Tamper
:
Mode
Functioning of the Siren
Disable
Do Not Select this Mode
Always ARMED
If this mode is selected then in case of
Tampering of Siren or wire cutting or removing
