Carrier PIC 5+, Инструкции по установке, эксплуатации и обслуживанию

Страница: 83 / 116

83
DSH_Req param VFD 1st 0.9427 0.9427
DSH_Req param VFD Const -34.5 -34.5
DSH_Req param IGV F 0.2 0.2
DSH_Req param IGV 2nd 0.0046 0.0046
DSH_Req param IGV 1st -0.562 -0.562
DSH_Req param IGV Const 21 21
DSH_Req param Lift F 0.3 0.3
DSH_Req param Lift 2nd 0.0006 0.0006
DSH_Req param Lift 1st -0.1104 -0.1104
DSH_Req param Lift Const 5.5 5.5
Liquid Bypass Temp Diff 11.1 11.1
Liquid Bypass Cond Appro 2.8 2.8
Bearing Sub Cooling -5 -5
Purge Discharge Temp -15.6 -15.6
Purge Drainage Temp -11.1 -11.1
CLT Factory Option disable enable
Refrig Lube Option 7 disable disable
TABLE CFGUMVFD - UM VFD Configuration
Access Menu Configuration Menu / UM VFD Configuration
Setting Default value (SI units) Settings value (SI) Comments
Compressor Speed 100% 50 Hz 98 Hz
Nameplate
Rated line voltage 460 V 400 V
Nameplate
Motor Nameplate Current 200 A
Nameplate
Motor Rated Load Current 200 A Nameplate
Motor Nameplate Voltage 460 V
Nameplate
Motor Nameplate RPM 3000 rpm
Nameplate
Motor Nameplate KW 1500 kW
Nameplate
Skip Frequency 1 102 Hz 102 Hz
UM Rockwell LF2
Skip Frequency 2 102 Hz 102 Hz UM Rockwell LF2
Skip Frequency 3 102 Hz 102 Hz
UM Rockwell LF2
Skip Frequency Band 0 Hz 0 Hz
Increase Ramp Time 30 sec 30 sec
Decrease Ramp Time 30 sec 30 sec
Line Voltage % Imbalance 0.1 10%
Line Volt Imbalance Time 10 sec 10 sec
Line Current % Imbalance 0.4 40%
Line Current Imbal Time 10 sec 10 sec
Motor Current % Imbalance 0.4 40%
Motor Current Imbal Time 10 sec 10 sec
Single Cycle Dropout Dsable Dsable
PWM Frequency (0=2 k Hz, 1=4 k Hz) 0 0
Restore Defaults No No
LEN Comm Timeout 10 sec 10 sec
Modbus Comm Timeout 2 sec 2 sec
Gateway Modbus Baud Rate
4800 = 1, 9600 = 2, 19200 = 3,
38400=4
2 2
Number of GDCBs 0 0
GDCB Startup Delay 50% 50%
TABLE CONF_OPT - Option configuration
Access Menu Configuration Menu / Option Configuration
Setting Default value (SI units) Settings value (SI)
Auto Restart Option Dsable job site specific
Common Sensor Option Dsable job site specific
EC Valve Option
No=0, Cont.=1, ON/OFF=2, mA=3
0 2 if selected
EC valve selection
Disable =0, Surge=1, Low Load=2, Comb=3
0 job site specific
ECV Open IGV1 Position 5% 5% (adjust as required)
ECV Close IGV1 Position 10% 10% (adjust as required)
ECV Off DT for Low Load 2,2 °C 2,2 °C (adjust as required)