Carrier 58MTB Скачать руководство пользователя | Manualshive

Страница: 12 / 60

background image

MINOR PROPERTY DAMAGE
Failure to follow this caution may result in minor property
damage.
Local codes may require a drain pan under entire furnace and
condensate trap when a condensing furnace is used in attic
application or over a finished ceiling.

NOTE:

The auxiliary junction box (J-Box) MUST be relocated to

opposite side of furnace casing. (See Fig. 13.) See Electrical
Connection section for J-Box relocation.

CONDENSATE TRAP LOCATION

The condensate trap must be removed from the factory-installed
blower shelf location and relocated in selected application location
as shown in Fig. 2 or 13.

To relocate condensate trap from the blower shelf to desired
location, perform the following:

1. Remove 3 tubes connected to condensate trap.

2. Remove trap from blower shelf by gently pushing tabs inward

and rotating trap.

3. Install casing hole filler cap (factory-supplied in loose parts

bag) into blower shelf hole where trap was removed.

CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury
or death.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the equipment
room.

4. Install condensate trap into right-hand side casing hole by

inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.

5. Fill unused condensate trap casing holes with plastic filler

caps (factory-supplied in loose parts bag).

CONDENSATE TRAP TUBING

NOTE:

See Fig. 13 or tube routing label on main furnace door to

check for proper connections.

1. Collector Box Drain Tube:

a. Remove factory-installed plug from LOWER collector box

drain tube (blue and white striped label).

b. Install removed clamp and plug into UPPER collector box

drain tube (blue label) which was previously connected to
condensate trap.

c. Connect LOWER collector box drain tube (blue and white

striped label) to condensate trap. Tube does not need to be
cut.

Fig. 11—Attic Location and Working Platform for Direct Vent (2-Pipe) Applications

A93031

COMBUSTION – AIR

INTAKE

VENT

MANUAL

SHUTOFF

GAS VALVE

SEDIMENT
TRAP

CONDENSATE
TRAP

DRAIN

ACCESS OPENING
FOR TRAP

30

″

MIN

WORK AREA

A 12-IN. MIN HORIZONTAL PIPE
SECTION IS RECOMMENDED WITH
SHORT (5 TO 8 FT) VENT SYSTEMS
TO REDUCE EXCESSIVE
CONDENSATE DROPLETS FROM
EXITING THE VENT PIPE.

5

3

⁄

4

″

NOTE: LOCAL CODES MAY REQUIRE A DRAIN PAN UNDER THE

FURNACE AND CONDENSATE TRAP WHEN A CONDENSING
FURNACE IS INSTALLED ABOVE FINISHED CEILINGS.

12

«
...
10
11
12
13
14
...
»

Содержание 58MTB





























































Отзывы:

Нет отзывов

Похожие инструкции для 58MTB

Бренд: Newmans Страницы: 13

Бренд: Lennox Страницы: 6

Бренд: Yumpu Страницы: 66

Бренд: Hotblast Страницы: 28

Бренд: Harman Stove Company Страницы: 41

Бренд: Continental Refrigerator Страницы: 88

Бренд: ICP Страницы: 36

Бренд: Westinghouse Страницы: 4

Бренд: Williamson-Thermoflo Страницы: 28

Бренд: Williamson-Thermoflo Страницы: 31

CARBOLITE GERO RHF 15/15

Бренд: VERDER Страницы: 34

CARBOLITE GERO RWF 11/23

Бренд: VERDER Страницы: 36

CARBOLITE GERO SNF

Бренд: VERDER Страницы: 42

CARBOLITE GERO STF 16/180

Бренд: VERDER Страницы: 46

Chamber Furnace 1500 deg.c.

Бренд: PIECO Страницы: 8

Бренд: Goodman Страницы: 14

Бренд: Goodman Страницы: 37

Бренд: Goodman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды