manualshive.com logo in svg

Carrier 58MTB, Инструкция по установке, запуску и эксплуатации

Carrier 58MTB - надежный продукт, обеспечивающий ваш комфорт. Установка, запуск и эксплуатация с легкостью благодаря руководству по установке, запуску и эксплуатации. Бесплатное скачивание руководства с {веб-сайта}. Наслаждайтесь удобством и эффективностью с Carrier 58MTB.

Поделиться
Скачать
background image

58MTB

Deluxe 4–Way Multipoise 2-Stage

Condensing Gas Furnace

Installation, Start-up, and Operating Instructions

Sizes 060-120, Series 100

NOTE:

Read the entire instruction manual before starting the

installation.

NOTE:

This furnace can be installed as a

direct vent (2-pipe)

or non-direct vent (1-pipe)

condensing gas furnace.

This symbol

→

indicates a change since the last issue.

TABLE OF CONTENTS

SAFETY CONSIDERATIONS .....................................................2

CODES AND STANDARDS........................................................3

Safety.........................................................................................3
General Installation...................................................................3
Combustion and Ventilation Air ..............................................5
Duct Systems ............................................................................5
Acoustical Lining and Fibrous Glass Duct..............................5
Gas Piping and Gas Pipe Pressure Testing..............................5
Electrical Connections ..............................................................5

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........6

INTRODUCTION ..........................................................................6

APPLICATIONS............................................................................6

General ......................................................................................6
Upflow Applications.................................................................6
Downflow Applications ............................................................8
Horizontal Left (Supply-Air Discharge) Applications ..........10
Horizontal Right (Supply-Air Discharge) Applications ........11

LOCATION..................................................................................14

General ....................................................................................14
Furnace Location Relative to Cooling
Equipment ...............................................................................15
Hazardous Locations...............................................................15
Furnace Location and Application .........................................15

AIR FOR COMBUSTION AND VENTILATION ....................16

INSTALLATION .........................................................................19

Leveling Legs (If Desired) .....................................................19
Installation in Upflow and Downflow
Applications ............................................................................19
Installation in Horizontal Applications ..................................19
Air Ducts.................................................................................19

General Requirements .......................................................19
Ductwork Acoustical Treatment .......................................21

Supply Air Connections ....................................................21
Return Air Connections.....................................................21

Filter Arrangement..................................................................21
Bottom Closure Panel.............................................................23
Gas Piping...............................................................................24
Electrical Connections ............................................................25

115-V Wiring.....................................................................25
24-V Wiring.......................................................................27
Accessories ........................................................................27

Removal of Existing Furnaces from Common Vent

Systems ..............................................................................28

Combustion-Air and Vent Pipe Systems ...............................28
Condensate Drain....................................................................42

General...............................................................................42
Application.........................................................................42
Condensation Drain Protection .........................................43

START-UP ADJUSTMENT AND SAFETY CHECK ..............43

General ....................................................................................43
Prime Condensate Trap With Water ......................................44
Purge Gas Lines......................................................................44
Sequence of Operation............................................................44

Two-Stage Heating With Single-Stage Thermostat
(Adaptive Mode)................................................................45
Two-Stage Heating With Two-Stage Thermostat
(Non-Adaptive Heating Mode) .........................................45
Cooling Mode ....................................................................46
Thermidistat Mode ............................................................46
Continuous Blower Mode .................................................50
Heat Pump .........................................................................50
Component Self-Test.........................................................50
Operate Furnace.................................................................51
Furnace Restart ..................................................................51

Adjustments.............................................................................51

Set Gas Input Rate ............................................................51
Set Temperature Rise ........................................................56
Adjust Blower Off Delay (Heat Mode)............................57
Set Thermostat Heat Anticipator ......................................57

Check Safety Controls ............................................................57
Checklist..................................................................................58

A93040

Visit www.carrier.com

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Book 1

4

Tab

6a 8a

PC 101

Printed in U.S.A.

Catalog No. 58MTB-1SI

Pg 1

8-05

Replaces: 58MTA-8SI

Содержание 58MTB





























































Отзывы:

Нет отзывов

Похожие инструкции для 58MTB

York DGAA056BDTA Installation Instructions Manual preview
DGAA056BDTA
Бренд: York Страницы: 28
Napoleon NCPF-110 Installation And Operating Instructions Manual preview
NCPF-110
Бренд: Napoleon Страницы: 28
Unitary products group FC9V Installation Manual preview
FC9V
Бренд: Unitary products group Страницы: 24
DENTSPLY Vulcan Box A-130 Owner'S/Operator'S Manual preview
Vulcan Box A-130
Бренд: DENTSPLY Страницы: 12
Carrier 59TP6A Installation, Start-Up, Operating And Service And Maintenance Instructions preview
59TP6A
Бренд: Carrier Страницы: 92
Coleman COMFORTEERTM GM8S Brochure & Specs preview
COMFORTEERTM GM8S
Бренд: Coleman Страницы: 4
Coleman Echelon FC8T Technical Manual preview
Echelon FC8T
Бренд: Coleman Страницы: 8
Walter Wilson OLR112A16A Installation Instructions And Homeowner'S Manual preview
OLR112A16A
Бренд: Walter Wilson Страницы: 48
Lyman Mag25 Operation And Assembly Instructions preview
Mag25
Бренд: Lyman Страницы: 8
Fedders FV95A Series Specifications preview
FV95A Series
Бренд: Fedders Страницы: 5
Barnstead|Thermolyne SET-TEMP limit Operating Instructions Manual preview
SET-TEMP limit
Бренд: Barnstead|Thermolyne Страницы: 12
Unitary products group PxDUA12V06401 series Installation Instruction preview
PxDUA12V06401 series
Бренд: Unitary products group Страницы: 28
ICP N9MP1 Service Manual preview
N9MP1
Бренд: ICP Страницы: 60
WarmFlo EC001 Installation & Operating Instructions Manual preview
EC001
Бренд: WarmFlo Страницы: 37
Warmington Gas Nouveau SN 900 Installation Instructions And Service Manual preview
Gas Nouveau SN 900
Бренд: Warmington Страницы: 19
Unitary products group G8C Installation Manual preview
G8C
Бренд: Unitary products group Страницы: 28
Coleman FC9M060B12UP11 Technical Manual preview
FC9M060B12UP11
Бренд: Coleman Страницы: 12
Unitary products group AUTOMATIC IGNITION FURNACES User'S Information Manual preview
AUTOMATIC IGNITION FURNACES
Бренд: Unitary products group Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды