Carrier 58MTB Скачать руководство пользователя

Страница: 41 / 60

Fig. 44—Combustion Air and Vent Pipe Termination

for Direct Vent (2-pipe) System (All Sizes)

A05090

At least 36 in.

18 in. maximum

Vertical separation
between combustion
air and vent
8 3/4 in. for 3 in. kit
6 3/4 in. for 2 in. kit

Roof Termination (Preferred)

Abandoned masonry
used as raceway
(per code)

At least

36 in.

Maintain 12

in.

min. clearance above
highest anticipated
snow level, maximum of
24 in. above roof

Concentric Vent and Combustion Air
Roof Termination (preferred)

in.

maximum (type)

in.

minimum from

overhang or roof

Maintain 12

in.

min. clearance above
highest anticipated
snow level or grade
whichever is greater

At lea

in.

Concentric Vent
and Combustion - Air
Side Termination

At least 36 in.

Side wall termination

of less than 12

in.

min from

overhang or roof

in.

separation

between bottom of
combustion air and
bottom of vent

Maintain 12

in.

min. clearance above
highest anticipated
snow level or grade
whichever is greater

At least 36 in

Maintain 12 in. min.
clearance above
highest anticipated
snow level
Maximum of 24 in.
above roof

Note: "A" denotes 0 to < 2 in.

Fig. 45—Vent Pipe Termination for Non-Direct

Vent (1-pipe) System (Sizes 040 Through 120 Only)

A05091

Abandoned masonry
used as raceway
(per code)

12 in. min. from

overhang or roof

Maintain 12 in.
minimum clearance
above highest anticipated
snow level or grade
whichever is greater.

Side wall termination
with 2 elbows (preferred)

12 in. min. from
overhang or roof

Maintain 12 in.
minimum clearance
above highest anticipated
snow level or grade
whichever is greater

6 in. minimum clearance

between wall and end of vent pipe.

10 in. maximum pipe length

Sidewall Termination

with Straight Pipe (preferred)

Roof Termination (Preferred)

Vent

Maintain 12 in.

minimum clearance

above highest anticipated

snow level maximum of

24 in. above roof.

→

Содержание 58MTB





























































Результаты поиска

Содержание 58MTB

Отзывы:

Похожие инструкции для 58MTB

Бренды по названию

Популярные бренды

Carrier 58MTB, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание 58MTB

Отзывы:

Похожие инструкции для 58MTB

Бренды по названию

Популярные бренды