Carrier 58MTB Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 60

background image

The air filter arrangement will vary due to application, furnace
orientation, and filter type. The filter may be installed in an
external Filter/Media cabinet (if provided) or the furnace blower
compartment. Factory supplied washable filters are shipped in the
blower compartment.

If a factory-supplied external Filter/Media cabinet is provided,
instructions for its application, assembly, and installation are
packaged with the cabinet. The Filter/Media cabinet can be used
with the factory-supplied washable filter or a factory-specified
high-efficiency disposable filter (see cabinet instructions).

If installing the filter in the furnace blower compartment, deter-
mine location for filter and relocate filter retaining wire if
necessary. See Table 4 to determine correct filter size for desired
filter location. Table 4 indicates filter size, location, and quantity
shipped with this furnace. See Fig. 2 for location and size of
bottom and side return-air openings.

Fig. 25—Crawlspace Horizontal Application for Direct Vent/2-Pipe Installation

and for Non-Direct Vent/1-Pipe Installation

A05054

NOTES:

ANGLE
IRON OR
EQUIVALENT

(B)

(A) ROD LOCATION

USING DIMPLE
LOCATORS
(SEE DIMENSIONAL
DWG FOR
LOCATIONS)

13

/

16

-IN. MAX

ALTERNATE SUPPORT
LOCATION FROM BACK

ALTERNATE SUPPORT
LOCATION 4-IN. MIN
8-IN. MAX

3

⁄

8-IN. ROD

(A)

(B)

(A)

(B)

(B)

(A)

1. A 1 In. clearance minimum between top of
furnace and combustible material.

2. The entire length of furnace must be
supported when furnace is used in horizontal
position to ensure proper drainage.

3. For non-direct vent/1-pipe application,
bottom side combustion-air entry cannot be
used when furnace is installed with hangers
as shown.

(A) PREFERRED ROD LOCATION

(B) ALTERNATE ROD LOCATION

DRAIN

5

3

⁄

4

″

3

/

8

-IN. HEX NUT

& WASHER (4)

REQD PER ROD

VENT

COMBUSTION-AIR PIPE
(DIRECT VENT/2-PIPE
APPLICATION,ALL SIZES)

COMBUSTION-AIR INTAKE
(NON-DIRECT VENT/1-PIPE
APPLICATION,SIZES 040
THROUGH 120 ONLY)

3-IN. MINIMUM CLEARANCE TO
COMBUSTION-AIR INTAKE IS REQUIRED
(NON-DIRECT VENT/1-PIPE
APPLICATION,SIZES 040
THROUGH 120 ONLY)

Table 4—Filter Information

AIR FILTER LOCATED IN BLOWER COMPARTMENT

FURNACE

CASING

WIDTH (IN.)

FILTER SIZE (IN.)*

FILTER

TYPE

Side Return†*

Bottom Return*

17-1/2

(1) 16 X 25 X 1

(1) 16 X 25 X 1

Cleanable

21

(1) 16 X 25 X 1

(1) 20 X 25 X 1

Cleanable

24-1/2

(1 or 2) 16 X 25 X 1

(1) 24 X 25 X 1

Cleanable

* Factory-provided with the furnace. Filters may be field modified by cutting
filter material and support rods (3) in filters. Alternate sizes and additional
filters may be ordered from your distributor or dealer.
† Upflow only. Alternate sizes and additional filters may be ordered from your
dealer.

22

→

→

«
...
20
21
22
23
24
...
»

Содержание 58MTB





























































Отзывы:

Нет отзывов

Похожие инструкции для 58MTB

Бренд: Valor Страницы: 18

Бренд: Yukon Eagle Страницы: 64

Бренд: York Страницы: 16

Бренд: Fedders Страницы: 5

Бренд: Unitary products group Страницы: 28

Бренд: Bard Страницы: 69

NTG3/FBF Series

Бренд: ICP Страницы: 47

NTC6/GNE Series

Бренд: ICP Страницы: 18

356486-UUM-E-0109

Бренд: Johnson Controls Страницы: 6

Бренд: Heat Controller Страницы: 40

Бренд: Weld Rite Страницы: 50

Бренд: USSC Страницы: 24

Бренд: Luxaire Страницы: 8

Бренд: Empire Heating Systems Страницы: 15

Бренд: Empire Heating Systems Страницы: 16

Бренд: Empire Heating Systems Страницы: 20

Бренд: Empire Heating Systems Страницы: 20

Бренд: Empire Heating Systems Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды