Carrier 58MTB Скачать руководство пользователя | Manualshive

Страница: 39 / 60

background image

EXAMPLE:
An 080-12 size furnace located in Indianapolis, elevation
650 ft above sea level, could be installed as either a direct
vent/2-pipe system that requires 3 elbows and 32 ft of vent
pipe, along with 5 elbows and 34 ft of combustion-air pipe
OR a non-direct vent/1-pipe system that requires 3 elbows
and 32 ft vent pipe.
For a direct vent/2-pipe system, Table 12 indicates this
application would allow a 2-in. diameter vent pipe, but
require a 2-1/2 in. diameter combustion air pipe. According
to Table 12, 2-in. diameter pipe is good for 35 ft with 3
elbows, but only 30 ft with 5 elbows. Therefore, 2-1/2 in.
diameter pipe must be used for both vent and combustion-
air pipes since larger required diameter must always be
used for both pipes.
For a non-direct vent/1-pipe system, Table 12 indicates that
this application would allow a 2-in. diameter vent pipe.
If same installations were in Albuquerque, elevation 5250 ft
above sea level:
For a direct vent/2-pipe system, Table 12 indicates that
2-1/2 in. diameter vent pipe and combustion-air pipe are
required.
For a non-direct vent/1-pipe system, Table 12 indicates that
2-1/2-in. diameter vent pipe is required.
If same applications are to be installed at 5001- to 6000 ft
elevation:
For a direct vent/2-pipe system, 2-in. pipe is only good for
23 ft (with 3 elbows) and 17 ft (with 5 elbows). Therefore,
2-1/2 in. diameter combustion air and vent pipe must be
used.
For a non-direct vent/1-pipe system, a 2-in. diameter pipe is
only good for 23 ft with 3 elbows. A 2-1/2-in. diameter vent
pipe must be used.

VENT TERMINATION

General

Combustion-air (direct vent/2-pipe system only) and vent pipe
must terminate outside structure, either through sidewall or roof.
For vent termination clearance, refer to Table 8 for Direct

Fig. 40—Pipe Grommets and Entry Hole Filler Plug Installation

COMBUSTION-AIR PIPE GROMMETS

GAS LINE GROMMET

GAS LINE

COMBUSTION
-AIR PIPE

VENT PIPE

VENT PIPE GROMMET

UNUSED 1/2 -IN.
DIAMETER GAS
CONN. HOLE

GAS LINE ENTRY
HOLE FILLER PLUG

NOTE: PIPE GROMMETS AND ENTRY HOLE FILLER
PLUGS ARE INCLUDED IN FACTORY-SUPPLIED
LOOSE PARTS BAG

A05057

Fig. 41—Combustion-Air and Vent Pipe Diameter

Transition Location and Elbow Configuration

A93034

FURNACE

PIPE DIAMETER

TRANSITION IN

VERTICAL SECTION

NOT IN
HORIZONTAL
SECTION

→

Fig. 42—Air Intake Housing Plug Fitting Drain

A05093

COMBUSTION-AIR
PIPE (DIRECT
VENT/2 PIPE)

BURNER
BOX

COMBUSTION – AIR
INTAKE HOUSING

3/8 ID TUBE

TRAP

TO OPEN

DRAIN

3/16

DRILL

4

″

MIN

COMBUSTION-AIR
PIPE (NON-DIRECT
VENT/1-PIPE)

39

→

→

→

«
...
37
38
39
40
41
...
»

Содержание 58MTB





























































Отзывы:

Нет отзывов

Похожие инструкции для 58MTB

Бренд: ICP Страницы: 27

Бренд: Goodman Страницы: 11

CARBOLITE GERO CWF 13/65

Бренд: VERDER Страницы: 36

Бренд: Payne Страницы: 49

PG8JAA Series G

Бренд: Payne Страницы: 52

Бренд: Payne Страницы: 62

Бренд: Lyman Страницы: 7

Бренд: Carrier Страницы: 10

Бренд: Haier Страницы: 38

Бренд: Clayton Страницы: 24

Бренд: Whip Mix Страницы: 32

Бренд: McQuay Страницы: 32

Бренд: Johnson Controls Страницы: 8

Бренд: Johnson Controls Страницы: 14

Бренд: Johnson Controls Страницы: 28

Бренд: Johnson Controls Страницы: 28

Бренд: Johnson Controls Страницы: 38

Бренд: Johnson Controls Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды