Carrier 39HXC Скачать руководство пользователя | Manualshive

Страница: 36 / 64

background image

5.2 - Modbus TCP/IP and BACnet IP

Configuring the board

Status LED

MAC address

Ethernet LED

Pushbutton
Earth connector

The board is factory fitted. If this is not the case, switch off the controller and insert the board in J13 (entitled BMS card or BMS1) on

the controller.

Press the button found on the board whilst switching the power to the controller back on. The left-hand LED will start to flash rapidly.

Keep pressing the reset button. After approximately 8 seconds, the left-hand LED (status LED) changes from green to red,

and then starts flashing. At this point, release the button.

Powered up

Release the button

Button pressed

Button

Button

Approx 8 s

Button released

Red

Green

The board is now initialised to the address 172.16.0.1. You will now need to configure your PC to a fixed IP.

Procedure for Windows 7:

Important: you must have administrator rights to your computer

Go to the

Start

menu on your PC then

Control Panel

.

In the Network and Internet section, click the link

View network status and tasks

.

5 - CONNECTION TO A CMS

36

«
...
34
35
36
37
38
...
»

Содержание 39HXC

































































Отзывы:

Нет отзывов

Похожие инструкции для 39HXC

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

R32 Split Series

Бренд: Daikin Страницы: 28

Clima-Flex CLIV Series

Бренд: Daikin Страницы: 46

Бренд: Panasonic Страницы: 53

Бренд: Stulz Страницы: 36

Бренд: Stulz Страницы: 28

Бренд: Daikin Страницы: 9

Бренд: TATA Motors Страницы: 32

Бренд: SystemAir Страницы: 72

Бренд: York Страницы: 56

Бренд: Valeo Страницы: 25

Бренд: Gree Страницы: 125

DIFFUSIONE 10.5 HP HE

Бренд: Olimpia splendid Страницы: 108

GWH09MA-K3DNA3L

Бренд: Gree Страницы: 89

GWH09UB-K3DNA4F

Бренд: Gree Страницы: 130

ArcticAire APA070B1G

Бренд: Danby Страницы: 26

Бренд: TriStar Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды