Carrier 39HXC Скачать руководство пользователя

Страница: 24 / 64

3.12 - CO

air quality

Before activating the air quality function (P152), you need to install a CO

sensor in the exhaust air flow, and connect it to the terminal

strip situated in the electrics box. Refer to the unit's manual for the installation and electrical connection.

This function calculates an IAQ (Indoor Air Quality) requirement thanks to a proportional controller (P217) so that the CO

concentration

setpoint (P216) can be monitored.

100%

Air quality

setpoint P216

Air quality proportional band

P217

IAQ requirement

Air quality

P331

If the fans are under flow rate control:

Air quality control acts primarily on the fresh air rate via the mixing damper (if present), if the fresh air rate reaches 100%,

the control system then acts on the ventilation flow rate, increasing the flow rate to a maximum value controlled by parameters P218

and P219.

Maximum flow rate

P218

Regulated flow

rate setpoint

(1 or 2)

IAQ requirement

100%

If the air intake fan is under duct pressure control (P104):

Warning: this function cannot be used if the heat recovery unit's frost level is monitored by a pressure sensor or if the extraction fan

is under duct pressure control.

In this scenario where the air intake fan is under duct pressure control, the air quality sensor must be connected to terminal strip

J26-U12.

The control function only acts on the opening value of the mixing damper to allow a greater influx of fresh air.

100%

% fresh air

Mixing minimum

opening percentage

1/2

IAQ requirement

100%

152

Air quality control

216

Air quality setpoint

217

Air quality proportional band

218

Air flow max setpoint on intake for air quality

219

Air flow max setpoint on exhaust for air quality

3.13 - Fire protection

When a DAD (standalone trigger sensor) is connected to the unit, the fire detection function of the control must be activated (P24).

There are several operating modes in case of fire detection:

Unit shut down

Intake fan forced to P282 flow rate and exhaust fan shut down

Exhaust fan forced to P283 flow rate and intake fan shut down

Intake fan forced to P282 flow rate and exhaust fan to P283 flow rate

Fire detection

280

Fire safety operating mode

282

Intake flow rate in case of fire

283

Exhaust flow rate in case of fire

ATTENTION : The fire fault management strategy must be chosen according to the regulations in force in the AHU's country

of installation. The AHU is not a smoke extraction device.

3 - FEATURES

Содержание 39HXC

































































Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды

Carrier 39HXC, Руководство пользователя

Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды