Carrier 39HXC Скачать руководство пользователя

Страница: 19 / 64

Supply air compensation

When control is being applied to the return air or room air, the supply air temperature can be compensated. This compensation is used

avoid blowing air at too cold or too high a temperature when the control is in deadband mode (no heating or cooling requirement

calculated). This compensation is activated by parameter P157.

Proportional band P235

Supply air

compensation

lower limit P234

Supply air

compensation

upper limit P236

Proportional band P237

Low

threshold

fault P240

High

threshold

fault P241

Heating compensation

(%)

Cooling compensation

(%)

Supply air temperature

100%

157

Supply air compensation in deadband = With or Without

234

Low supply air temperature compensation setpoint in deadband

235

Low supply air temperature compensation proportional band in deadband

236

High supply air temperature compensation setpoint in deadband

237

High supply air temperature compensation proportional band in deadband

The temperature upper and lower thresholds (P240 to P245) are used to trigger a fault if the temperature is outside of these limits.

240

Supply air temperature low limit threshold

241

Supply air temperature upper limit threshold

242

Return air temperature low limit threshold

243

Return air temperature upper limit threshold

244

Room temperature low limit threshold

245

Room temperature upper limit threshold

3.7 - Fan control

The controller runs the plug fans with an EC motor. The unit has one intake fan and one exhaust fan. Pressure sensors for measuring

the air flow rate are wired on the PLC.
The fans can be under constant duct flow rate control or constant duct pressure control.

Constant air flow control (P104)

The flow rate setpoints are configurable: Intake flow rate setpoints 1 / 2 (P112, P113) and exhaust flow rate setpoints 1 / 2 (P128, P129)

The PID for the intake motor control is managed via P114 to P116, and the exhaust motor control via P130 to P132

Intake flow

112

Air intake fan flow rate setpoint 1

113

Air intake fan flow rate setpoint 2

114

Air intake fan flow control PID proportional band (P)

115

Air intake fan flow rate control PID integral time (I)

116

Air intake fan flow rate control PID derivative time (D)

Extraction flow

128

Air extraction fan flow rate setpoint 1

129

Air extraction fan flow rate setpoint 2

130

Air extraction fan flow rate control PID proportional band (P)

131

Air extraction fan flow rate control PID integral time (I)

132

Air extraction fan flow rate control PID derivative time (D)

3 - FEATURES

Содержание 39HXC

































































Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды

Carrier 39HXC, Руководство пользователя

Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды