Carl Valentin Dynacode II Series Скачать руководство пользователя | Manualshive

Страница: 36 / 122

background image

Installation and Initial Operation

Dynacode II Series

36

Operating Manual

08.16

7.3 Connection of Pneumatic Power Supply

The pneumatic power supply for the printhead mechanics has to be
made available a minimum continuous pressure of 4 - 6 bars in front
of the pressure regulator. The maximum pressure in front of the
pressure regulator is 7 bars and 4 bars after the pressure regulator.

NOTICE!

A pneumatic power supply of 4 bars is recommended.

The compressed-air has to be dry and oil free.

The supplied pressure regulator with manometer is to connect with a
pneumatic tube Ø 8 mm via a plugging bolting to the pneumatic power
supply. It is necessary to make a connection between the pressure
regulator and the print mechanics via a pneumatic tube Ø 8 mm.

Please observe the following notes:



Position pressure regulator as near as possible to the print
mechanics.



The pressure regulator is only to operate in the direction that is
indicated on its underside. The direction shows the way of the
streaming air.



It is not allowed to bend the pneumatic tubes.



Shortening of the pneumatic tubes has to be made with a clean
right-angled cut without squashing the tube. If necessary use
special tools (available in pneumatic requirements).



Please observe a possible short length of the 8 mm pneumatic
tubes.

Druckmechanik

Druckluftversorgung

Pneumatikschlauch

min. 4 bar, max. 7 bar

Druckregler mit Manometer

Print mechanics

Pneumatic power supply

Pneumatic tube 8x1

Pressure regulator with manometer

Figure 29

«
...
34
35
36
37
38
...
»

Содержание Dynacode II Series



























































































































Отзывы:

Нет отзывов

Похожие инструкции для Dynacode II Series

Бренд: U-Line Страницы: 20

Бренд: Oki Страницы: 76

Бренд: Galaxy Equipment Страницы: 5

Espresso Automatic EA83 Series

Бренд: Krups Страницы: 194

Бренд: Viking Страницы: 12

GRAND CAFE BOLOGNA 242137

Бренд: Princess Страницы: 28

Бренд: T-Fal Страницы: 24

Nespresso Vertuo Creatista

Бренд: Sage Страницы: 28

Бренд: Rancilio Страницы: 34

Бренд: La Pavoni Страницы: 8

Бренд: Rombouts Страницы: 10

Бренд: LAVAZZA Страницы: 106

Бренд: Ice-O-Matic Страницы: 2

Бренд: RTC Страницы: 17

Бренд: IMPRESSA Страницы: 60

Бренд: VKI Technologies Страницы: 36

Dinamica Plus ECAM37X.95

Бренд: DeLonghi Страницы: 26

Бренд: Hoshizaki Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды