Carl Valentin Dynacode II Series Скачать руководство пользователя страница 81

Страница: 81 / 122

Dynacode II Series

Maintenance and Cleaning

08.16

Operating Manual

11 Maintenance and Cleaning

DANGER!

Risk of death by electric shock!



Disconnect the direct print module from power supply
before performing any maintenance work.

NOTICE!

When cleaning the label printer, personal protective equipment
such as safety goggles and gloves are recommended.

Maintenance task

Frequency

General cleaning
(see chapter 11.1, page 81).

As necessary.

Cleaning transfer ribbon roller
(see chapter 11.2, page 82).

Each time the transfer ribbon is
changed or when the printout is
adversely affected.

Cleaning printhead
(see chapter 11.3, page 81).

Each time the transfer ribbon is
changed or when the printout is
adversely affected.

Replacing printhead
(see chapter 11.4, page 83).

In case of errors in printout.

NOTICE!

The handling instructions for the use of Isopropanol (IPA) must
be observed. In the case of skin or eye contact, immediately
wash off the fluid thoroughly with running water. If the irritation
persists, consult a doctor. Ensure good ventilation.

11.1 General Cleaning

CAUTION!

Abrasive cleaning agents can damage the direct print
module!



Do not use abrasives or solvents to clean the outer
surface of the direct print module.



Remove dust and paper fuzz in the printing area with a soft
brush or vacuum cleaner.



Clean outer surfaces with an all-purpose cleaner.

Maintenance
chedule

Содержание Dynacode II Series



























































































































Результаты поиска

Содержание Dynacode II Series

Отзывы:

Бренды по названию

Популярные бренды

Carl Valentin Dynacode II Series, Руководство по эксплуатации

Результаты поиска

Содержание Dynacode II Series

Отзывы:

Бренды по названию

Популярные бренды