Carl Valentin Dynacode II Series Скачать руководство пользователя страница 3

Страница: 3 / 122

Dynacode II Series

Table of Contents

08.16

Operating Manual

Table of Contents

Table of Contents ............................................................................. 3

Introduction ............................................................................ 5

1.1

General Instructions ................................................................ 5

1.2

Intended Use ........................................................................... 5

1.3

Safety Instructions ................................................................... 6

Machine Overview ................................................................. 9

2.1

Connection Side of Print Mechanics ....................................... 9

2.2

Connector Assignment of Control Unit .................................. 10

Continuous Mode ................................................................ 11

3.1

Material Speed ...................................................................... 11

3.2

Print Principle ........................................................................ 11

3.3

Material Guiding .................................................................... 12

Intermittent Mode ................................................................ 13

4.1

Print Principle ........................................................................ 13

4.2

Print Position ......................................................................... 13

Operating Conditions .......................................................... 15

Technical Data ..................................................................... 19

6.1

Control Inputs and Outputs (Standard) ................................. 21

6.2

Control Inputs and Outputs (Option) ..................................... 26

6.3

Registered functions/profiles for inputs/outputs .................... 30

6.4

Pin Assignment of Encoder Socket ...................................... 32

Installation and Initial Operation ........................................ 33

7.1

Installation of Print Mechanics at Machines .......................... 34

7.2

Required Space for Cable Outgoing ..................................... 35

7.3

Connection of Pneumatic Power Supply ............................... 36

7.4

Adjustment of Pressure Power .............................................. 37

7.5

Connecting the Direct Print Module ....................................... 38

7.6

Before Initial Operation .......................................................... 38

7.7

Print Control ........................................................................... 39

7.8

Initial Operation ..................................................................... 39

Loading the Transfer Ribbon Cassette ............................. 41

8.1

Transfer Ribbon With Coating Outside.................................. 41

8.2

Transfer Ribbon With Coating Inside .................................... 42

8.3

Increasing the Clamping Force for Ribbon Roll .................... 43

Function Menu ..................................................................... 45

9.1

Menu Structure (Continuous Mode) ...................................... 45

9.2

Menu Structure (Intermittent Mode) ...................................... 48

9.3

Print Settings ......................................................................... 51

9.4

Machine Parameters (Continuous Mode).............................. 52

9.5

Machine Parameters (Intermittent Mode) .............................. 54

9.6

Layout .................................................................................... 56

9.7

Ribbon Save (Continuous Mode) .......................................... 57

9.8

Ribbon Save (Intermittent Mode) .......................................... 58

9.9

Device Settings ...................................................................... 58

9.10

I/O Parameters ...................................................................... 60

9.11

Network ................................................................................. 60

9.12

Remote Console .................................................................... 61

9.13

Interface ................................................................................. 61

9.14

Emulation ............................................................................... 62

9.15

Date & Time ........................................................................... 63

9.16

Service Functions .................................................................. 64

9.17

Main Menu ............................................................................. 66

Содержание Dynacode II Series



























































































































Результаты поиска

Содержание Dynacode II Series

Отзывы:

Похожие инструкции для Dynacode II Series

Бренды по названию

Популярные бренды

Carl Valentin Dynacode II Series, Руководство по эксплуатации

Результаты поиска

Содержание Dynacode II Series

Отзывы:

Похожие инструкции для Dynacode II Series

Бренды по названию

Популярные бренды