Carl Valentin Dynacode II Series Скачать руководство пользователя

Страница: 21 / 122

Dynacode II Series

Technical Data

08.16

Operating Manual

6.1 Control Inputs and Outputs (Standard)

Figure 7

A = Output 1

Port 9-12

B = Input 1

Port 1-4

C = Output 2

Port 13-16

D = External bushing
D = 15pin (I/O-24)

Port 1 + 9

By means of the signal outputs different operating states of the print
module can be queried.

The signal outputs are provided by two 9-pin SUB-D-bushings
(OUTPUT I and OUTPUT II) on the back side of the control unit.

They consist of optocoupler semiconductor sections, which are
connected through and/or blocked according to different operating
states.

The maximum allowable current in a semiconductor section is

lmax = 30 mA.

Output I
Figure 7, A

Figure 8

PIN (bushing)

Output I

Out 1 / Port 9: Error message

Each error status such as ribbon
error is displayed.

Out 2 / Port 10: Print order

The print module was activated by a
print order.

Out 3 / Port 11: Generation

The print module is filled with current
layout data.

Out 4 / Port 12: Layout print

The content of print memory is
transferred on the printable medium
by means of the printhead.

Plug connection - back
side of control unit

Control outputs

Содержание Dynacode II Series



























































































































Результаты поиска

Содержание Dynacode II Series

Отзывы:

Похожие инструкции для Dynacode II Series

Бренды по названию

Популярные бренды

Carl Valentin Dynacode II Series, Руководство по эксплуатации

Результаты поиска

Содержание Dynacode II Series

Отзывы:

Похожие инструкции для Dynacode II Series

Бренды по названию

Популярные бренды