Carefree FREEDOM FREESTYLE WM Скачать руководство пользователя страница 10

Страница: 10 / 24

REEDOM

REESTYLE

WM Service

Manual

Carefree of Colorado

052573-301r8

15. Secure the pivot assembly to the case connector with the retaining clip.

16. Slide the arm onto the lead rail connector and secure using the pin and clip removed previously.

17. For the LH arm, route the cable through the wire channel. At the arm joints, arch the cable slightly to

avoid binding. Do not twist the cable.

Tip: Use a small tool, such as a flat bladed screwdriver to gently spread open the channel then insert
the cable. Do this for the entire length of the channel until the cable is fully inserted.

18. Remove the supports from the lead rail.

19. After replacing the arm, it will be necessary to adjust the pitch to align the lead rail and case. See page 7.

20. Adjust the motor limits as required. See page 13.

EPLACING THE

EAD

AIL

ONNECTOR

1. Remove the arm according to the instructions on page 5.

2. Remove the lead rail end plate.

3. Carefully measure and mark the location of the existing connector

and ramp and sensor (when installed).

4. Loosen the securing screw and slide the existing ramp from the

lead rail.

5. Loosen the screws on the sensor. Twist the brackets slightly and lift the sensor and brackets away from the

lead rail. Disconnect the module from the wire harness. Quick connects are found behind the module.

6. Loosen the securing screw and slide the existing connector from the lead rail.

7. Insert the new connector assembly into the lead rail and position at the marks made previously.

NOTICE

Failure to position the connector correctly will cause the arm and lead rail not to close

correctly.

8. Tighten the outer securing screw.

9. For the sensor cable. Route the cable behind the new connector. Reconnect the module to the wire

harness. Position the module and brackets and tighten the screws.

10. Install the ramp.

11. Attach the lead rail end plate.

12. Return to “Replacing the Arm” on page 5.

Remove

End Plate

Ramp

Arm

Connector

FF015

Direct

Response

Module

Содержание FREEDOM FREESTYLE WM

























Результаты поиска

Содержание FREEDOM FREESTYLE WM

Отзывы:

Похожие инструкции для FREEDOM FREESTYLE WM

Бренды по названию

Популярные бренды

Carefree FREEDOM FREESTYLE WM, Руководство по обслуживанию

Результаты поиска

Содержание FREEDOM FREESTYLE WM

Отзывы:

Похожие инструкции для FREEDOM FREESTYLE WM

Бренды по названию

Популярные бренды