Canon LaserBase MF3220 Series, Руководство по обслуживанию

Страница: 111 / 124

Chapter 5
5-3
5.4 Service Mode
5.4.1 Outline
5.4.1.1 Service Data Setting
0012-6439
Service mode has the following service data items. These items can be
checked/changed according to the menu on the display.
SERVICE'S CHOICE
Use it to select service data to suit the country/region of installation, to reset
the user data, or to set the transmission/reception speed.
ADJUST
Use it to execute margin adjustment for printing or reading.
VERSION DISPLAY
Use it to indicate version information on the display.
SOFT SWITCH
00AE Can't finished V.8 procedure or detect V.21 signal after CM signal
00AF
Modem can't enter into control channel after TX side sending out RCP signal
for V34
00B1 Can't finish V.8 procedure or detect V.21 signal after ANSam signal within 35 sec.
00B2 Can't detect phase 2 signal after our side sending CJ signal within 30 sec
00B3 Can't detect correct V.21 or JM signal after sending CM or CJ signal.
00B4 Can't detect correct phase 2 signal within 25 second after CM/JM signal exchange.
00B5 Can't detect phase 3 signal after Phase 2
00B6 Can't detect phase 4 signal within 25 sec after CM/JM exchange.
00B8 Remote side disconnect after our side sending DCS signal in V.34.
00BA Cannot received correct signal after our side sending DTC signal in V.34.
00BB Every time our side received DIS signal after sending DTC in V.34.
00BC Modem can't ready within 10 second after entering primary channel in V.34.
00BD Can't detect correct V.21 or JM signal after detected FSK frequency.
00BE Remote side no document to be polled after V.8 handshaking.
00BF Capability no match after V.8 handshaking
00C1
At phase-D, transmitting units out EOP 3 times consecutively, but receive no answer from receiving
unit.
00C2 Remote side disconnect after sending out V.8 CM signal.
00C4 After sending MPS signal, the received is not one of MCF, RTN, PIP, PIN, RTP, DCN.
00C5 Received DCN signal after sending MPS signal.
00C9 At phase D, sending MPS 3 times consecutively, but no answer from receiveing unit.
00CA After sending EOP signal, the received is not one of MCF, RTN, PIP, PIN, PRI-EOP, DCN, RTP.
00CB After sending EOP signal, the received is DCN signal.
00CF Received incorrect signal after sending DTC signal for V.34 polling.
00D0 Received ERR signal after sending EOR_NULL.
00D1 Received incorrect response after sending PPS_EOP signal
00D2 Received DCN after sending PPS_EOP signal
00D3 Received DCN after sending PPS_NULL signal
00D8 Can't detect correct phase 3 signal for poling.
00D9 Can't detect correct phase 3 signal after detect silence after phase 2.
00DA Can't detect phase 4 signal within 30 sec.
00DB Can't received any T.30 signal within 30 sec within phase 4.
00DC Received T.30 signal in phase 4 other than DCS, DIS or DTC
00DE Remote side no SUB capability.
00E0 At phase-D, transmitting units out PPS_NULL 3 times consecutively but receive not answer.
00E1 Received incorrect response after sending PPS_NULL.
00E2 Can't receive any response in RR response procedure after sending PPS_NULL.
00E4 At phase D, transmitting units out PPS_MPS 3 times consecutivery but receive no answer.
00E5 Received incorrect response after sending PPS_MPS signal
00E6 Can't receive any response in RR response procedure after sending PPS_MPS.
00E7 Reseived DCN after sending PPS_MPS.
00E8 At phase-D, transmitting units out PPS_EOP 3 times consecutively but receive no answer.
00E9 Receive PIN signal after sent last page data.
00EA Can't receive any response in RR response procedure after sending PPS_EOP.
00EE At phase-D, transmitting units out EOR_NULL 3 times consecutively but receive no answer.
00EF Received incorrect response after sending EOR_NULL.
00F0 Can't receive any response in RR response procedure after sending EOR_NULL.
00F1 At phasa-D, transmitting units out EOR_MPS 3 times consecutively but receive no answer.
00F2 Received incorrect response after sending EOR_MPS.
00F3 Received ERR signal after sending EOR_MPS.
00F4 Can't receive any response in RR response procedure after sending EOR_MPS.
00F5 At phasa-D, transmitting units out EOR_EOP 3 times consecutively but receive no answer.
00F6 Received incorrect response after sending EOR_EOP
00F7 After Received ERR, our side can't received response after sending EOR_EOP command.
00FC Can't receive any response after sending CTC.
00FD Can't speed down to lower speed.
00FE Memory full for transmission
00FF REDAIL ALL FAIL
Error Code Description