Canon LaserBase MF3220 Series, Руководство по обслуживанию

Страница: 110 / 124

Chapter 5
5-2
0030 Can't receive any signal within 6 sec. At phase D.
0031 Received incorrect signal at phase D (not EOP, MPS, EOM, DCN, PPS_Q, PPS_Q,etc)
0032 Can't receive carrier within 6 sec after sending MCF or RTP, RTN signal
0033 Received DCN signal at ohase D within pages (not last page).
0039 In non_ECM mode, when machine alredy received the data dosen't receive 13.1 seconds
001F Can't detect any G3 signal within 35 sec after sending DTC signal
003F Remote side TSI not define in machine one touch or speed dial directory
0040 Can't receive carrier within 6 sec. after sending CTR.
0041 Can't receive carrier within 6 sec. after sending PPR.
0042 Can't receive correct signal after sending RNR signal
0043 Receive incorrect signal at phase D in ECM mode.
0044 Can't receive carrier/FSK signal within 6 sec. After sending MCF. ln ECM mode.
0047 Can't receive correct signal or DCN received after sending ERR signal.
0048 Can't receive correct signal after receive PPS_PRI_Q
004B Can't detect correct FSK signal even through detected FSK tone within 6 sec.
004C Handshake fail during re-train or between page in V34 Rx.
004E Receive DCN signal after sending DIS in V.34.
004F Remote side disconnected after sending ANSam in V.8 phase.
0050 Can't receive any correct signal after detected CJ signal in V.8 phase.
0051 Can't receive phase 3 signal after phase 2 within 20 seconds in V.34.
0053 Modem disconnect after phase 4 in V.34.
0054 Remote side disconnect after phase 4 in V.8
0055 Receive incorrect signal after sending DIS signal in V.34
0056 Modem disconnect after sending CFR in V.34
0058 Can't detect image signal within 6 sec after modem enter to primary phase in V.34
005A Modem cannot detect any correct ECM frame with 3 minutes in phase C.
005B Modem can't detect control channel with 12 sec in phase C
005C Detect busy tone within control channel after phase C.
005D Modem can't detect any correct ECM frame with 12 sec in phase C.
005E Can't detect control channel signal after received RCP frame within 6 sec
005F Can't detect silence after sending JM signal for polling TX function.
0060 There are no any bullietin files to be polled in V.34.
0061 Machine cannot detect V.21 or V.8 signal with 35 sec.
0062 Modem disconnect in phase D after our side sending out flags sequence in control channel.
0063 Can't receive any flag sequence in control channel within 25 sec in phase D.
0064
Can't detect any control channel signal in phase D within 60 sec even through energy still on the
line.
0065 Can't detect any control channel signal within 60 sec after detect sillence in phase D.
0066 Can't receive T.30 signal or carrier after sending CFR in V.34.
0069 Capability no match paper size after received is DCS signal.
0070 User press stop key within receiving.
0071 Memory full within receiving.
0080 Can't detect any G3 signal within 35 sec. specified by ITU-T in phase B.
0081 Received DTC signal in transmission phase.
0082 Transmitting unit receives a signal other than DIS or DTC. And DCN in phase B.
0083 Detected FSK signal, but Can't receive any signal within 35 sec.
0084 Detect DCN signal in phase B.
0085 Transmitting unit sending DCS 3 times consecutively, but each time responds with DIS/DTC
0086 Detected responds signal other than DTC,DIS,FTT,DCN or CFR after sending DCS.
0087 Training attempt has failed because speed unit can't adjust to low lower speed.
0088 Received DCN signal after sending out DCS signal
008B Receivers protcol of DIS is received, but it is not compatible with our machine.
008C Remote side or our side not support capability.
008D
Receivers protocol of DIS is received, but remote side can't receive document temporary, may
because by run out of paper or other reason.
008F Modem not ready to received V.34 data within 6 sec after received CFR signal.
0090 Called side document not ready for our polling.
0091 Can't receive any commabd after send DCN signal 3 times consecutively
0093 Received DCN signal after sending out DCN signal
0094 Time out during transmit ECM frame or RCP command.
0095 Wrong ID number
0096 SUBADDRESS/PASSWORD capability not match in polling Rx mode.
009A Can't detect any signal after sending CI signal.
009D Remote side hang up before V.34 modem enter phase 2 state in V.34 polling Rx.
009E Manual Tx over 15 minutes whin in phase C by non-ECM mode.
00A0 User stop or cancel transmission job.
00A1 Document JAM within transmission
Error Code Description