background image

Symptom

Possible cause

Suggested action

Unable to connect to
the network; or nei-
ther LED on the
10/100/1000BaseT
network connector is
lit

One of the following:

• Wrong cable. Do not use a crossover

cable.

• Wrong port. Do not use the printer port.

The printer port is reserved for the print-
er and for installing system software
from a PC.

• Faulty network cable or connection
• Faulty network
• Faulty Ethernet port on the mother-

board

1. Make sure that the network cable is the correct type and con-

nected to the designated LAN port on the 

imagePRESS Server

connector panel.

2. Check the cable connection to the network.
3. Replace the cable with a new or tested cable.
4. Request that the network administrator check Network Setup.
5. Request that the network administrator check other devices on

the network.
If other devices are not functioning, there could be a problem
with the network.

6. If the rest of the network is functioning properly and the prob-

lem persists, replace the motherboard.

System starts up
slowly (seems to
hang) and the Con-
figuration page dis-
plays an error on the
“IP Address” line un-
der “Network Setup”

One of the following:

• Normal behavior

System is searching for a nonexistent
DHCP server.
DHCP is enabled by default on the 

im-

agePRESS Server

, but the customer’s

network is not using DHCP.

• If the customer’s network is using

DHCP:

• Network cable or connection is

faulty

• Network is faulty
• Faulty Ethernet port on the moth-

erboard

1. Request that the network administrator change the default in 

imagePRESS Server

 Network Setup.

2. If neither LED on the designated network port is lit on the 

im-

agePRESS Server

, check the cable connection to the 

image-

PRESS Server

 and the network. Make sure that the cable is

the correct type.

3. If the network cable is the correct type and is properly con-

nected to the 

imagePRESS Server

, connect a new network

cable to the 

imagePRESS Server

.

4. Request that the network administrator check other devices on

the network.
If other devices are not functioning, there could be a problem
with the network.

5. Replace the motherboard.

Scanning
Problems with scan-
ning or sending files

• Loose, incorrect, or missing connection

between the 

imagePRESS Server

 and

printer

• The printer does not have an IP ad-

dress

1. Check and reseat the printer interface cable between the 

im-

agePRESS Server

 and the printer.

2. Power off/on the printer.
3. Replace the printer interface cable.

Printing

NOTE:

Intermittent print quality problems are difficult to trace. Before you try to troubleshoot print quality problems, print a test page to
make sure that the printer itself does not need servicing or adjusting.

Test page fails to
print

Print engine is not ready to print

1. Make sure that the printer is powered on and ready to print.
2. Check the printer touch panel for indications or messages

about the printer status.

There is a problem with the connection be-
tween the 

imagePRESS Server

 and the

printer

1. Make sure that the 

imagePRESS Server

 LED is lit. If not, press

the power switch to turn on the 

imagePRESS Server

.

2. Power off/on the printer.

NOTE:

Power off the printer using the main power switch on the
front.

3. Make sure the network and scanning options are available

from the printer touch panel.

4. Check again that the printer interface cable is present and

properly connected to the 

imagePRESS Server

 and the print-

er.

5. Check again that the printer interface board is present and

properly connected to the motherboard.

6. Replace the printer interface cable.
7. Replace the printer interface board.
8. If the problem persists, you may need to service the printer.

Corrupted system software

Reinstall system software.

5. TROUBLESHOOTING

73

Содержание imagePRESS Server M10



































































































Отзывы: