Canon imagePRESS Server M10 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 98

background image

5. At the Select Flash drive window, click the USB flash drive that you attached to the computer, and click Next.

If more than one USB devices are displayed, make sure to select the USB flash drive that you attached for loading the system
software.
A warning message “This USB flash drive will be formatted and all the data in this USB flash drive will be lost.” appears.
Click Next to format the USB flash drive and proceed.

IMPORTANT:

All the data on the USB flash drive will be lost when you format the USB flash drive. Make sure that no valuable data is
stored on the device.

NOTE:

It may take approximately 30 to 40 minutes to format the USB flash drive and load the files on to the drive. Do not interrupt the
operation.

6. Once the preparation is done, safely disconnect the USB flash drive from the computer.

You can use this USB flash drive as a source for system software installation.

■ Install the system software using the prepared USB flash drive

You can install the system software using the prepared USB flash drive.

● To install the system software

1. Remove all the USB devices that may be connected to the

imagePRESS Server

.

4. INSTALLING SYSTEM SOFTWARE

59

«
...
63
64
65
66
67
...
»

Содержание imagePRESS Server M10



































































































Отзывы:

Нет отзывов

Похожие инструкции для imagePRESS Server M10

Бренд: IBM Страницы: 198

eServer BladeCenter HS20Type 8832

Бренд: IBM Страницы: 158

ProLiant DL180 Gen10

Бренд: HPE Страницы: 10

Бренд: SafeNet Страницы: 109

totalstorage 200

Бренд: IBM Страницы: 180

Бренд: Axel Страницы: 28

Бренд: AIC Страницы: 101

Бренд: Netstor Страницы: 17

Бренд: RIOT Страницы: 18

Бренд: Tiger Technology Страницы: 29

Бренд: Viavi Страницы: 8

AirProjector KJ-200

Бренд: TriLink Страницы: 56

IMS LANTIME M500

Бренд: Meinberg Страницы: 132

Бренд: SeeedStudio Страницы: 19

NAS TS-877XU-RP-3600-8G-US

Бренд: QNAP Страницы: 12

Бренд: QNAP Страницы: 15

Бренд: FreeNAS Страницы: 4

Бренд: AMX Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды