Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 137

background image

Trouble Shooting Information for C7000VP series

Page 18

Rev. 2.0

2010/09/17

1.16

E514-8001 only at first power-on in the morning

Due to slight weight difference observed when comparing the shifting load of assist plate, the

rail assembly in the photograph below was disassembled and cleaned, and grease was also

reapplied.

1.17

E578



Description

When copying 50 sheets of coated paper of 128g in weight in 2-point staple mode, an error of

paper folding position for saddle stitching occurred and the error code E578 was displayed.

- E578 can be displayed when the feed belt HP sensor does not go ON or OFF within 5 sec
after the feed belt shift motor operation starts. (Knurling error)



Cause

This machine stapled more than the specified number of sheets at a time.



Field Remedy

Before making copies, check paper type and the number of sheets to be stapled at a time.

Reference:

The following describes the specifications for stapling.

Weight of paper

# of sheets applicable (Small size / Large size)

64g to 80g

100sh / 50sh

Over 80g to 81.4g

80sh / 50sh

Over 81.4g to 105g:

60sh / 30sh

Over 105g to 200g:

20sh / 10sh

Over 200g to 300g:

Cover and back cover only

Note:

- Thickness of stack has to be less than 11mm for small size, and less than 5.5mm for large
size.
- Length of paper in feeding direction has to be as follows.



For large size: 216.1mm to 482.7mm (e.g. 13x19, 12x18, SRA3, A3, B4, A4R, B5R,

LDR, LGL, LTRR, EXER)



For small size: shorter then 216mm (e.g. A4, B5, A5R, LTR, EXE, STMTR)

«
...
16
17
18
19
20
...
»

Содержание imagePRESS C7000VP Series










































































































































Отзывы:

Нет отзывов

Похожие инструкции для imagePRESS C7000VP Series

image Prograf iPF785 Series

Бренд: Canon Страницы: 136

Бренд: GBC Страницы: 110

iP2600 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 8

ImageCLASS 2300

Бренд: Canon Страницы: 102

CLP-680ND: CLP-775ND

Бренд: Samsung Страницы: 2

Бренд: Xerox Страницы: 168

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 64

Бренд: Xerox Страницы: 54

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 115

Бренд: Lexmark Страницы: 2

Бренд: Durst Страницы: 2

Aficio SP4100N-KP

Бренд: Ricoh Страницы: 4

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

Бренд: J&Maya Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды