Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 137

Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 121

Trouble Shooting Information for C7000VP series

Page 121

Rev. 2.0

2010/09/17

In IMAGE PRIORITY mode

MAP for primary fixing assembly control temperatures

64g

80g

106g 129g 151g 181g 210g 257g

～

～

～

～

～

～

～

～

79g

105g 128ｇ 150g 180g 209g 256g 300g

Plain

One-sided coated
Two-sided coated

Recycled

Embossed

Film/label

Vellum

Cotton

default control temperature
Media not supported

MAP for secondary fixing assembly control temperatures

64g

80g

106g 129g 151g 181g 210g 257g

～

～

～

～

～

～

～

～

79g

105g 128ｇ 150g 180g 209g 256g 300g

Plain

One-sided coated
Two-sided coated

Recycled

Embossed

Film/label

Vellum

Cotton

default control temperature
Media not supported
ANY （Media fed only to primary fixing）

★Note on IMAGE PRIORITY mode

※ For 2-sided coated media of 80-105gsm in basis weight and LTR-R or smaller in size, the control
temperature is set commonly in IMAGE PRIORITY and PRODUCTIVITY PRIORITY modes.
(To maintain feeding performance, the temperature is set lower than the control temperature normally
set for 2-sided coated media of 80-105gsm in basis weight.)

The status enters "Adjusting the fixing unit. Wait for a moment." if the control temperature is changed from the
setting either in the primary or secondary fixing assembly.

Surface nature

Basis weight

Surface nature

Basis weight

«
...
119
120
121
122
123
...
»

Содержание imagePRESS C7000VP Series










































































































































Отзывы:

Нет отзывов