Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 113

Страница: 113 / 137

Trouble Shooting Information for C7000VP series

Page 113

Rev. 2.0

2010/09/17



Adjusting the Secondary Transfer Voltage of a Custom Paper Type

1. Press [Change] next to <Secondary Transfer Voltage>.

2. Press [-] or [+] under <Front Side> or <Back Side> to adjust the voltage > press [OK].

The secondary transfer voltage is applied when toner is transferred to paper. When lighter

image or image blurring occurs on custom paper as compared with standard paper, adjust the

voltage according to the table below.

Cases where adjustment in [-] direction
is recommended

Cases where adjustment in [+] direction
is recommended

Paper
Weight

Light (thin paper)

Heavy (thick paper)

Image
failure

Density in high-density areas is normal;
but tiny white spots may appear in the
low-density areas.

Density level in both high- and
low-density areas is low.

White spots appear on the high-density
areas.

Uneven glossy areas may occur in the
high-density images.

Paper surface is rough (such as
embossed paper) and white spots may
appear on the concave side.

Outlines in high-density images may
blur.

Note: Changing this setting may affect the settings in [ITB Image Clear Adjustment], [ITB Paper

Detachment Adjust.], and [Tail End White Patch Correct.]. Readjust these settings, if necessary.



Adjusting the Gloss of a Custom Paper Type

1. Press [Change] next to <Gloss Adjustment>.

2. Press [-] or [+] to adjust the gloss > press [OK].

The Gloss Adjustment mode enables you to adjust the gloss on printed image by adjusting the

temperature of the fixing assembly. Press [+] to increase the gloss, and press [-] to decrease

the gloss. Depending on the paper type, if you change the setting value, the temperature of the

fixing assembly may also be changed. In addition, the paper may pass through only the primary

fixing assembly or both the primary and secondary fixing assemblies.

Содержание imagePRESS C7000VP Series










































































































































Результаты поиска

Содержание imagePRESS C7000VP Series

Отзывы:

Похожие инструкции для imagePRESS C7000VP Series

Бренды по названию

Популярные бренды

Canon imagePRESS C7000VP Series, Информация по устранению неполадок

Результаты поиска

Содержание imagePRESS C7000VP Series

Отзывы:

Похожие инструкции для imagePRESS C7000VP Series

Бренды по названию

Популярные бренды