Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 105

Страница: 105 / 137

Trouble Shooting Information for C7000VP series

Page 105

Rev. 2.0

2010/09/17

5.2

Specifications for staple capacity of Finisher-AB1/AB2



Description

The following are specifications for staple capacity of Finisher-AB1/AB2 by basis weight of

paper (both small and large sizes).

Weight of paper

# of sheets applicable (Small size / Large size)

64g to 80g

100sh / 50sh

over 80g to 81.4g

80sh / 50sh

over 81.4g to 105g:

60sh / 30sh

over 105g to 200g:

20sh / 10sh

over 200g to 300g:

Cover and back cover only

Note:

- Thickness of stack has to be less than 11mm for small size, and less than 5.5mm for large
size.
- Length of paper in feeding direction has to be as follows.



For large size: 216.1mm to 482.7mm (e.g. 13x19, 12x18, SRA3, A3, B4, A4R, B5R,

LDR, LGL, LTRR, EXER)



For small size: shorter then 216mm (e.g. A4, B5, A5R, LTR, EXE, STMTR)

Reference:

Although the staple capacity of the aforementioned Finisher units is specified like the above, on

requests from the field, the units were so designed that they staple more than the number of

sheets described above with regard to all basis weights in case the total number of sheets to be

stapled is set within 100 sheets. But, please be informed that a problem may occur when the

units staple more than the number specified above.

5.3

Number of sheets and size specification for saddle stitching



Description

- Paper size applicable for saddle stitching:



12 x 18, SRA3 (320 x 450), A3, B4, A4R, LDR, LTRR, LGL

- Basis weight:



Inner sheets:

64 to 200g/mx2



Cover: 64 to 300g/x2

- Maximum number of sheets for binding:



20 sheets (Inner sheets (64 to 80g/mx2) 19 Cover (64 to 300g/mx2) 1 sheet

Plain paper

64 to 80g/mx2

2 to 20 sheets (incl. cover)

81 to 105g/mx2

2 to 15 sheets (incl. cover)

Over 105 to 200g/mx2

2 to 5 sheets (incl. cover)

Coated paper

80 to 81.4g/mx2

2 to 15 sheets (incl. cover)

81.5 to 105g/mx2

2 to 10 sheets (incl. cover)

Over 105 to 200g/mx2

2 to 5 sheets (incl. cover)

Содержание imagePRESS C7000VP Series










































































































































Результаты поиска

Содержание imagePRESS C7000VP Series

Отзывы:

Похожие инструкции для imagePRESS C7000VP Series

Бренды по названию

Популярные бренды

Canon imagePRESS C7000VP Series, Информация по устранению неполадок

Результаты поиска

Содержание imagePRESS C7000VP Series

Отзывы:

Похожие инструкции для imagePRESS C7000VP Series

Бренды по названию

Популярные бренды