Canon imagePRESS C7000VP Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 137

background image

Trouble Shooting Information for C7000VP series

Page 20

Rev. 2.0

2010/09/17

1.20

E750-0002



Description

There are some reported instances from the field where, when the machine was relocated the

necessary work was done according to the procedure ‘Relocating the Machine.’ At this time,

however, not the drawer connector mount but each connector was detached from the backside

of the sub station. This caused an error in plugging each connector at the new installation place,

ultimately leading to the error code E750-0002.

- E750-0002 can be displayed when the model name informed by the main controller does
not match with that stored in the DC controller (i.e., same series but different model).



Cause

Communication error occurred between the DC controller software and the main controller

software because the connectors were plugged mistakenly.



Field Remedy

Although it's difficult to identify a connector plugged to the wrong jack from the error code, when

the same error occurs at time of relocation of this machine or service work for the drawer

connector mount, check to see if each connectors are connected to the correct jack.

Note:

When detaching/re-attaching the drawer connector to connect the main station and sub station

during installation or relocation, be sure to work not by the connector but by the drawer

connector mount to prevent errors in plugging connectors.

1.21

E750-2012



Description

There are some reported instances from the field where, at time of replacement of the fixing
intermediate assembly (FM2-9291) the two short connectors for identifying the destination

failed to be reattached, resulting in the error code E750-2012.

- E750-2012 can be displayed when the combination of the DC controller software and the
fixing assembly is not correct.



Field Remedy

When replacing the fixing intermediate assembly, be sure to follow the cautions described in

Appendix 3 ‘Points to Note When Replacing Primary/Secondary Fixing Intermediate Unit.’

«
...
18
19
20
21
22
...
»

Содержание imagePRESS C7000VP Series










































































































































Отзывы:

Нет отзывов

Похожие инструкции для imagePRESS C7000VP Series

Бренд: Xerox Страницы: 73

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 167

Бренд: Oki Страницы: 116

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 331

Бренд: Oki Страницы: 36

C5800Ldn Series

Бренд: Oki Страницы: 143

Бренд: Oki Страницы: 101

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 282

Бренд: Oki Страницы: 269

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 3

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды