Canon CLBP-460PS Скачать руководство пользователя страница 285

Страница: 285 / 566

Action:

Replace it if the belt in the feed belt unit is cut or the feed belt roller is damaged or
worn.

18) Damaged gears

Action:

Check the drive gears of the feed belt. Replace them if damaged or worn.

[ 3-4 ] Fixing and delivery block
<Possible causes>

1) If the paper is jammed after the fixing unit, go to step 11).

2) Upper or lower fixing roller does not rotate smoothly.

Action:

Replace them if fixing unit drive gears or the lower roller drive gear is worn or frac-
tured.

3) Projection on the fixing unit entrance guide, upper or lower fixing separation guide due to

dirt, scars, or toner attachment.

Action:

Clean the guide. Replace it if scarred or damaged.

4) Scar/deformed upper and lower fixing rollers

Action:

Replace the rollers.

5) Defective fixing unit delivery sensor lever

Action:

Adjust the lever correctly if it does not move smoothly or is out of position. Or,
replace it if damaged or deformed.

6) Worn fixing unit delivery roller

Action:

Replace the fixing unit delivery roller.

7) Damaged fixing unit delivery roller drive gears

Action:

If any gears are damaged or worn, replace them.

8) Projection on the deflector due to dirt, scars, or toner attachment.

Action:

Clean the face-up deflector if dirty. Replace it if scarred or deformed.

9) Worn face-down delivery roller

Action:

Replace the face-down delivery roller.

10) Defective face-down delivery roller/drive belt

Action:

Replace the face-down delivery roller gear if worn or fractured. Or, if the drive belt
is cut, replace it.

11) Defective DC controller PCB

Action:

Replace the DC controller PCB.

[ 3-5 ] Duplexing unit block
<Possible causes>

1) Execute a test print. Go to step 9) if the paper is jammed in the duplexing feed unit.

2) Worn/deformed reversing roller

Action:

Replace the reversing roller if worn or damaged.

4 - 31

CHAPTER 4

Содержание CLBP-460PS






















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CLBP-460PS

Отзывы:

Похожие инструкции для CLBP-460PS

Бренды по названию

Популярные бренды

Canon CLBP-460PS, Руководство по обслуживанию

Результаты поиска

Содержание CLBP-460PS

Отзывы:

Похожие инструкции для CLBP-460PS

Бренды по названию

Популярные бренды