manualshive.com logo in svg

Canon CLBP-460PS, Руководство по обслуживанию, Страница: 193 / 566

Поделиться
Скачать
Canon CLBP-460PS Скачать руководство пользователя страница 193

< Notes for reassembly of pick-up/feed drive units >

When drive unit of the pick-up/feed system has been disassembled, reassemble the gears as
shown in the figure bellow.
When replacing the gears in the figure below, apply grease to the gears and shafts to prevent
noise.  Type of grease and application method are described below.  Do not use grease other than
the ones specified here.

Lubricating material:HY9-0007

Apply 0.2g of EM50-L to the teeth of the gears specified in the figure bellow. 

Lubricating oil:CK-8003

Apply a drop to the shafts in the figure below.  Do not apply to the one way gear or clutch.

Figure 3-4-6

3 - 23

CHAPTER 3

29/17T

29T

18/52T

52T

34/15T

37T

47T

26T

24/37T

35T

20T

29T

16T

37/14T

31T

30/16T

27T

18T

49T

39/31T

53T

18T

19T

Feed/fixing system drive gear

Pick-up system drive gear

Содержание CLBP-460PS























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов