manualshive.com logo in svg

Canon CLBP-460PS, Руководство по обслуживанию

Поделиться
Скачать
Canon CLBP-460PS Скачать руководство пользователя страница 258

B. Initial Check

Check the following items before you diagnose malfunction.  If any failure is found, the service
technician is to clear the problem and to give the instruction to the user.

1. Installation environment

a. The line is ±10% of the rated voltage.
b. The printer is securely installed on a level surface.
c. The room temperature is kept between 10 and 30ÞC, and the relative humidity, between 10

and 80%.

d. Avoid sites generating ammonia gas, high temperature or high humidity (near water faucet,

kettle, humidifier), cold places, open flames, and dusty area.

e.

Avoid sites exposed to direct sunlight.  If unavoidable, advise the customer to hang curtains.

f.

A well-ventilated place.

g. Make sure that the power plug is inserted to the printer and the outlet securely. (Also, check

the power plug of the duplexing unit at the installation of the duplexing unit.)

2. Paper checks

a. The recommended paper for the printer is used.
b. The paper is not damp.
c.

CANON original OHT (OHT T-H1) is not used when OHT sheet is used.

3. Paper sets

a. The paper is set to the pick-up source within the specified volume.
b. The paper is set to the selected pick-up source correctly.  When OHT sheet is used, the sheet

is set to the multi-purpose tray correctly.

4. Toner cartridge sets

a. The color toner cartridges for each color are set correctly.

5. Drum cartridge sets

a. The drum cartridge is set to the printer correctly.

6. Units set

a. The ITB unit and fixing unit are set to the printer correctly.

7. Door/drawer set

a. All of the top cover, rear cover, drum cartridge drawer, and ITB unit drawer are closed.

8. Condensation

During winter, particularly when moving the printer into a warm room from a cold location such
a warehouse, various problems can occur due to condensation in the printer.

Example)

a. Condensation in the optical system (six-faced mirror, mirror, lens, etc.) will result in the light

print image.

b. As the photosensitive drum is cold, the resistance of the photo-conductive layer is high.  This

will lead to incorrect contrast.
If condensation appears, either wipe the parts with dry cloth, or leave the printer ON for 10
to 20 minutes.

If a toner cartridge is opened soon after being moved from a cold room to a warm room, con-
densation may appear inside the cartridge and may cause various problems.

4 - 4

CHAPTER 4

Содержание CLBP-460PS























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды