Canon CLBP-460PS Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 566

background image

5. PRINTER SETUP menu

The PRINTER SETUP menus are used to set PDL, paper size, and the ability to print using low
toner.

The submenus in the PRINTER SETUP menus are shown below. (Default values are in square

brackets.)

Note:

If “STOP” is selected, “TONER LOW” appears in the message area and print operation
stops when any of the toner cartridges becomes “Toner Low”. In such case, press the
ENTER key to resume printing. “TONER LOW” remains in the message area. The print-
er can keep printing until “TONER OUT” appears in the message area. Note that the
printer stops printing after power cycle.
If “CONTINUE” is selected, “TONER LOW” appears in the message area and print oper-
ation is continued until “TONER OUT” appears.

6. PS (PostScript) SETUP menu

The PS SETUP menus allow you to make settings relating to the PostScript printer.

The submenus in the PS SETUP menus are shown below. (Default values are in square

brackets.)

1 - 33

CHAPTER 1

Submenu

PAGE DESC LANG

DEFAULT PAPER
SIZE

TONER LOW

ENABLE SMOOTHING

PS/PCL/AUTO [AUTO]

LETTER/A4

CONTINUE/STOP
[STOP]

YES/NO [YES]

Options

Remarks

Use this submenu to select a default
PDL for your printer. If you select
“AUTO”, the printer will automatically
detect and interpret PDL used by the file.
Use this submenu to specify the default
paper size to print on. Default paper
size is Letter for USA, and A4 for other
areas.
Use this submenu to specify the behav-
iour of the printer when toner in a car-
tridge is low. Select “CONTINUE” to
print even when toner is low. Select
“STOP” to stop printing when the toner
is low.

(Note)

Use this submenu to conduct smoothing
(AIR) on the data to be printed.

Submenu

PRINT TO ERR

YES/NO [NO]

Options

Remarks

Use this submenu to specify whether the
portion of a print job processed before
encountering a PostScript error is print-
ed. Select YES to print the portion of
the job that was processed and a
description of the PostScript error, which
may help you troubleshoot the error.
Select NO to cancel printing when a
PostScript error is encountered.

«
...
41
42
43
44
45
...
»

Содержание CLBP-460PS























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CLBP-460PS

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 858

PAPERANG MonoSnap Lite

Бренд: Xiamen Страницы: 7

Бренд: Olivetti Страницы: 74

Бренд: Xerox Страницы: 150

Бренд: Flashforge Страницы: 44

Бренд: Jolimark Страницы: 65

Бренд: Konica Minolta Страницы: 285

DocuColor 45087638

Бренд: Xerox Страницы: 28

Бренд: imagistics Страницы: 2

Бренд: Wasp Страницы: 82

PRICOM PRICOM C- 5100

Бренд: Silex technology Страницы: 7

Бренд: Citizen Страницы: 255

WorkCentre 5687

Бренд: Xerox Страницы: 28

Dynacode II IP107

Бренд: Carl Valentin Страницы: 168

7400DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 2

Бренд: DataCard Страницы: 5

Бренд: Sharp Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды