manualshive.com logo in svg

Canon CLBP-460PS, Руководство по обслуживанию, Страница: 108 / 566

Поделиться
Скачать
Canon CLBP-460PS Скачать руководство пользователя страница 108

3. Development block
a. Outline

The development block consists of four toner cartridges and a developing rotary in which the
cartridges are installed.

The developing rotary is turned by the developing rotary motor (M3).  The developing rotary

contains Bk (black), M (magenta), C (cyan), and Y (yellow) toner cartridges, each of which faces
the photosensitive drum in sequence.  When a toner cartridge faces the photosensitive drum,
the developing cylinder is brought closer to the drum by the slider.

The developing cylinder of the cartridge is rotated by the toner cartridge motor (M5).
The developing rotary unit has three sensors: developing rotary position sensor, toner car-

tridge contact sensor, and toner level sensor.

Figure 2-4-6

2 - 50

CHAPTER 2

PS10

DC controller PCB

Toner cartridge

PS11

PS12

PS10: Developing rotary position sensor
PS11: Toner cartridge contact sensor
PS12: Toner level sensor

Slider

Developing
cylinder

M3

M5

Y

M3: Developing rotary motor
M5: Toner cartridge motor

ITB unit

Developing PCB

Photo-

sensitive

drum

Drum cartridge

DEVELOPING ROTARY POSITION DETECTION signal (/

ROTHP)

TONER LEVEL DETECTION signal (T

ONSNS)

TONER CARTRIDGE CONTACT DETECTION

signal (/DEVCAM)

DEVELOPING ROTARY 

MOTOR DRIVE signals

TONER CARTRIDGE

MOTOR DRIVE signals

Содержание CLBP-460PS























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов