Canon CLBP-460PS Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 566

Canon CLBP-460PS Скачать руководство пользователя страница 47

1 - 37

CHAPTER 1

Submenu

ETHERNET

ETHERNET SPEED

TOKEN RING

TR SPEED

MAX FRAME SIZE

SOURCE ROUTING

REQ ALL ROUTE

RESP ALL ROUTE

PARALLEL PORT

I/O TIMEOUT

IGNORE EOF

ON/OFF [ON]

10 TWISTED PAIR/
10 AUI/ 10
AUTO/100/
AUTODETECT
[AUTODETECT]
ON/OFF [ON]

4 MBPS/16 MBPS/
AUTO DETECT
[AUTO DETECT]

0.5K/1K/2K/4K [4K]

ON/OFF [OFF]

ON/OFF [OFF]

ON/OFF [OFF]

ON/OFF [ON]

5-300 [15]

YES/NO [YES]

Options

Remarks

Select “ON” to enable Ethernet network
communication.
Select “AUTODETECT” to automatically
detect the speed at which data can be
transferred over the Ethernet network,
or optionally specify the speed of your
Ethernet network.
Select “ON” to enable Token Ring net-
work communication.
Select “AUTO DETECT” to automatically
detect the speed at which data can be
transferred over the Token Ring net-
work, or optionally specify the speed of
your Token Ring network.
Selects the maximum frame size for
Token Ring network communication.
Specifies whether or not to allow the
packet to travel to its destination
through routers on the network.
Specifies whether or not to allow all
routers on the network to broadcast the
presence of the printer, enabling packets
from clients on the network to travel to
the printer by any route. Displayed
when “REQ ALL ROUTE” is set to “OFF”.
Specifies whether or not to allow all
routers on the network to broadcast the
presence of the client to the printer,
enabling packets from clients on the
network to travel to the printer by any
route. Displayed when “SOURCE
ROUTING” is enabled.
Select “ON” to enable printing through
the parallel port.
Specifies how long the printer waits
without receiving data from the parallel
port before deciding that the current job
is complete.
Displayed only when “PARALLEL PORT”
is set to “ON”.
Specifies whether or not the printer
should ignore end-of-file (EOF) messages
in a file. Select “YES” to use the value
you entered for “TIMEOUT” to determine
when it has reached the end of the file.
Displayed when “PARALLEL PORT” is
set to “ON”.

«
...
45
46
47
48
49
...
»

Содержание CLBP-460PS























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды