background image

CBP-436(2017) Operation and Maintenance Manual-CTS Tractors

Camso |  12-17 | 33

3. Ensure the o-ring on the hub is 

in place behind the cover and 

tighten the six bolts holding the 

cover to the hub. Torque bolts 

to 132 in-lbs (11 ft-lbs) 15 Nm.

4. Remove the plug in the center 

of the cover and refill each axle 

hub until the oil get out of the 

filling port. It’s approx. 0.25 

quarts (0.24 liters) of lubricant. 

Once filled, install plug.

Note:

refill the hub by using a 

syringe or a pump oil can.

WARNING

Lubricants should not to be poured in the environment. Collect them in 

suitable containers and deliver to licensed companies for waste 

disposal in accordance with the present law in force.

Avoid any contact of the lubricant with the rubber parts. If oil is spilled 

onto the track, clean oil from track surface with dry towel. Do not use

cleaning solvents or diesel fuel to clean oil from track surface as track 

damage may occur.

WARNING

Use only high quality lubricants with the same characteristics shown in 

“Lubricant table” section, stored in sealed containers according to 

manufacturer specifications.

Содержание 30/36D23MC

















































Отзывы: