![background image](http://html1.mh-extra.com/html/campbell-hausfeld/chn10310/chn10310_operating-instructions-manual_3771006006.webp)
6
Operating Instructions
CHN10302, CHN10310
www.chpower.com
User - Maintenance
Instructions
CLEARING A JAM FROM THE TOOL
1. Disconnect the air
supply from the
tool.
2. Remove all nails
from the magazine
(see Loading/
Unloading).
Failure to remove
all fasteners will
cause the fasteners to eject from the
front of the tool.
3. Undo latch by
pulling out
and down. The
wire latch will
disengage from
the hooks on the nose.
4. The door can
now be rotated,
exposing the
jammed fastener.
5. Remove the
jammed fastener,
using pliers or
a screwdriver if
required.
6. Rotate door back
into the closed
position.
7. Extend the wire
latch and place
over the hooks on
the nose.
8. Close the latch by
pushing the latch
up and in until the
latch snaps into
place.
9. Make sure the
trigger and work
contact element
(WCE) move freely
up and down
without sticking or binding.
TECHNICAL SERvICE
Please call our Tool Hotline at 1-800-
543-6400 with any questions regarding
the operation or repair of this tool or
for additional copies of this manual.
FASTENER AND REPLACEMENT
PARTS
Use only headless
micropins, 18 gauge.
Tool performance, safety and durability
could be reduced if improper fasteners
are used. When ordering replacement
parts or fasteners, specify by part
number.
TOOL REPAIR
Only qualified personnel should repair
the tool and they should use genuine
Campbell Hausfeld replacement parts
and accessories, or parts and accessories
which perform equivalently.
ASSEMbLY PROCEDURE FOR SEALS
When repairing a tool, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. After
reassembling, a few drops of 30W
non-detergent oil or equivalent, must
be added through the air line before
testing.
STORAGE
The tool should be stored in a cool dry
place.
Fasteners
The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call
customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.
Model
Length
Wire
Diameter
Crown
Size
Point
Finish
Collation
Nails Per
Stick
Nails Per
Box
FN180615AV
1/2 inch
18 Gauge
1/4 inch
Chisel
Galvanized / Vinyl Coated
Adhesive
100
1000
FN180620AV
3/4 inch
18 Gauge
1/4 inch
Chisel
Galvanized / Vinyl Coated
Adhesive
100
1000
FN180625AV
1 inch
18 Gauge
1/4 inch
Chisel
Galvanized / Vinyl Coated
Adhesive
100
1000
FN180630AV
1-1/4 inch
18 Gauge
1/4 inch
Chisel
Galvanized / Vinyl Coated
Adhesive
100
1000
Interchange Information
Staples used in the Finishing Stapler will also work in: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S,
KN-1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100.