CAME PXC08, Руководство по программированию

Страница: 33 / 36

ENGLISH
Page
33
- Manual:
FA00458-EN
- vers.
1
- 04/2017 - © C
AME S.p.A. - The data and information shown in this manual ar
e t
o be consider
ed as subject t
o change at any time and without the need for any advance warning.
Events messaging
Events are made up of:
• TIME and DATE
• EVENT DESCRIPTION (activation / restoration)
• EVENT INDEX NUMBER
• EVENT DESCRIPTION (part 2)
ACTIVATING RESTORING DESCRIPTION 2 CAUSE
Telephone notifications group
Alarm Sabot
age
Technical Burglar
y
Arming Failure Code Ke
y
Entrance Various
ARMING
TOTAL
Areas on
There is an arming event when the only
operations are (total or partial) arming.
When arming all of the areas managed by
the control unit, the second description
will read TOTAL, whereas for partial arm-
ing the areas on will be shown (example
##--#).
X
PARTIALIS. Areas on
There is a partialisation event when there
are operations of non-total disarming
of areas (partial disarming). The second
description will show the on/off status
of the remaining areas (example ##--#).
X
DISARMING
There is a disarming event when the sys-
tem is totally off.
X
TAMPER xx ALRM. RST, TAMPER xx
SECURITY ALARM
PWR.DESCR.
Tampering with an opening or a viola-
tion at the control unit or an auxiliary
power supply unit has been detect-
ed. Check the integrity and the tamper.
X
ALA.INP.TAMP. xxx RES.INP.TAMP. xxx
INPUT DESCR.
Input xxx has been tampered with (ei-
ther cut or short-circuited depending
on the balancing). Check the integri-
ty of the input's electricity line. Even
if it has restored itself "on its own",
check the input's electricity line be-
cause there could still be faulty contacts.
X
AREA ALARM xx AREA ALRM RST xx AREA DESCR.
When an input goes into alarm mode so do
the associated areas.
X
INP. ALARM xxx RESTORE INPUT xxx
INPUT DESCR.
Input xxx has gone into alarm mode (it has
been unbalanced).
X
BATTERY TX xxx INPUT DESCR.
Radio input xxx's battery is dead. Replace
it as soon as possible.
X
KYP.COM.ERR. xx KEYPAD DESCR.
Keypad xx is no longer communicating
with the control unit (red communication
LED on keypad not flashing). Check activa-
tion of keypad, bus cabling, address.
X
IN-MOD. ERR. xx MODULE DESCR.
The inputs expansion module on bus xx is
no longer communicating with the control
unit (red communication LED on module
not flashing). Check activation of module,
bus cabling, dip switch address.
X
OUT-MOD. ERR. xx MODULE DESCR.
The outputs expansion module on bus xx is
no longer communicating with the control
unit (red communication LED on module
not flashing). Check activation of module,
bus cabling, dip switch address.
X
RADIO.MOD.ERR. xx MODULE DESCR.
The radio receiver module on bus xx is no
longer communicating with the control
unit (red communication LED on module
not flashing). Check activation of module,
bus cabling, dip switch address.
X
RADIO MOD.JAM. xx MODULE DESCR.
The radio receiver module on bus xx has
detected a radio transmission that could
block any radio transmitters (JAMMING
function activated on control unit).
X
TX SUPERVIS. xxx
INPUT DESCR.
Radio input xx has transmitted a per-
son-detected communication.
IN-MOD.T-ALRM xx MODULE DESCR.
The tamper device on the inputs expansion
module on bus xx has been tampered with.
Check module tamper.
X
OUT-MOD.T-ALM xx MODULE DESCR.
The tamper device on the outputs expan-
sion module on bus xx has been tampered
with. Check module tamper.
X