Calsense CS3000 страница 39 Скачать руководство пользователя

Страница: 39 / 85

CS3000 User’s Guide

Calsense

Percent Adjust

The Percent Adjust feature provides the ability to increase or decrease the run times of ALL stations

assigned to a Station Group for a predetermined amount of time. This feature is typically used to

accommodate for upcoming weather events such as heat waves or heavy expected rain.

Note:

If Days

are set to zero, Percent Adjust is not in effect.

To edit the Percent Adjust screen (Figure 26):

From Main Menu, navigate to

Scheduled Irrigation

and select

Percent Adjust

. The Percent

Adjust screen displays.

Navigate to desired station group

Navigate to Percentage column and use the

+/-

to adjust the run time percentage.

Navigate to Days column and use the

+/-

to adjust the number of Days the adjustment will be in

effect.

The End Date will correspond with the days adjusted and show the date at which the

adjustment is no longer in effect.

When finished, press

BACK

to save changes, and return to Main Menu.

Figure 26: Percent Adjust Screen

Содержание CS3000






















































































Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды

Calsense CS3000, Руководство пользователя

Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды