Calsense CS3000 страница 17 Скачать руководство пользователя

Страница: 17 / 85

CS3000 User’s Guide

Calsense

POC Decoder

The Calsense POC 2-Wire decoder (model CS-2W-POC) operates a single master valve and Calsense Flow

Meter (model FM). A single controller can operate up to six POC decoders with a maximum of 12-POCs

in a chain of controllers using

FLOWSENSE

technology (Figure 7).

Soil Moisture Sensor Decoder

The Calsense soil moisture sensor is used to accurately measure the volumetric water content at the

depth at which the sensor is placed, by measuring the dielectric constant of the soil using

capacitance/frequency domain technology. It is used to maintain soil water balance for optimum plant

growth and to manage the amount of irrigation water applied.

The model CS-2W-MOIST is used in conjunction with the 2-Wire option, model CS3-2WIRE-OPT offered

only with the Calsense model CS3000 irrigation controller. The dual sensor/ decoder comes with the

standard 16-foot cable for proper sensor placement and the ability to wire one remote control valve to

the 2-Wire cable. Moisture sensors can be installed anywhere on the 2-Wire path up to 7,000 ft. of total

cable length.

Smart technology enables assigning any decoder’s serial number associated with a specific moisture

sensor location, to a group of like stations at the controller. The model CS3000 uses the sensor reading

measured at the beginning of each irrigation cycle compared to the user defined set point to determine

when to stop irrigation.

Figure 7: POC Decoder

Содержание CS3000






















































































Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды

Calsense CS3000, Руководство пользователя

Результаты поиска

Содержание CS3000

Отзывы:

Похожие инструкции для CS3000

Бренды по названию

Популярные бренды