Cajun P220G страница 18 Скачать руководство пользователя

Страница: 18 / 135

Configuring the P220G Gigabit Switch

Cajun P220G Switch Configuration and Operation Guide

2-3

10. Enter the following commands to give the Supervisor Module’s network interface

an IP address and default gateway to assign addresses to the Web Agent for inband
access over the network:

P220G Switch> net ip address inband <ip address> <ip mask>

P220G Switch> net ip default_gateway inband <address>

Note: Do not use the same IP address for both the console port and the inband

connection. Each interface must have a unique IP address, and be on a
separate IP subnetwork.

Note: You can have only one default gateway address. You must decide whether

the gateway address should be on the inband or out-of-band Ethernet
console port.

Depending on which IP addresses you have assigned, you can connect to the
system either in-band or out-of-band using the 10Base-T port on the front panel.
To connect using the console 10Base-T port, complete the following steps:

1. Attach a 10Base-T-compliant crossover cable to the RJ-45 connection in the switch

front panel listed in Table 2-2. The other end is assumed to be connected to an
Ethernet endstation such as a PC.

Note: If you are connecting the console Ethernet to a repeater or switch port, a

straight-through 10Base-T cable must be used. If you are connecting to an
endstation (such as a PC), a cross-over 10Base-T cable must be used.

Table 2-2. Pinouts for 10Base-T Crossover Patch Cables

2. Log in to the switch using a web browser, as described in the “Logging into the Web

Agent” section, later in this chapter.

WBr

Содержание P220G








































































































































Результаты поиска

Содержание P220G

Отзывы:

Похожие инструкции для P220G

Бренды по названию

Популярные бренды

Cajun P220G, Руководство по конфигурации и эксплуатации

Результаты поиска

Содержание P220G

Отзывы:

Похожие инструкции для P220G

Бренды по названию

Популярные бренды