background image

 DAMC-FMC2ZUP User’s Manual 

 

Module Management Controller 

24 
 

3.3

 

HPM update  

The MMC Stamp currently supports in-application-update of its firmware using 

the PICMG HPM.1 standard. Upcoming MMC firmware releases will also be able to 

update FPGA images. 

 

The firmware upgrade can be done with ipmitool using a command like this: 

 

ipmitool  -H  <mch_address>  -B  0  -b  7  -T  0x82  -t  <amc_ipmb_address>  hpm 
upgrade /path/to/firmware.hpm 

 

 

3.4

 

XMODEM update  

For situations where update through IPMI is not viable, all available HPM targets 

can also be updated via XMODEM over the serial USB. The update has to be initiated 

with the 

xm

 console command. 

 

3.5

 

FPGA boot mode selection  

The  ZUP  boot  mode  can  be  set  to  JTAG,  first  or  secondary  flash,  SD  card  or 

PJTAG. The Spartan-7 boot mode can be set to JTAG, first or secondary flash. 

 

Example commands: 

 

bz sd

   will configure the ZUP to boot from SD card; 

b7 spi2

   will configure the Spartan-7 to boot from the secondary SPI flash; 

rz will

   reconfigure the ZUP; 

r7

   will reconfigure the Spartan-7. 

 

3.6

 

Interlock multiplexing  

The  interlocks  can  be  multiplexed  between  sources  rx19,  tx19,  rx20,  zup  and 

targets out0, out1, out2. 

 

Example command: 

ci out1 tx19

    will route interlock TX19 to interlock out1. 

 

 

Содержание DAMC-FMC2ZUP



































Отзывы: