84
Serviceanleitung / Service Manual
/
/
/
Fehlermeldung
A/D-Wandler
defekt
dRAM defekt
FPGA defekt
LCD defekt
ROM defekt
Setup ungültig
Spannungsfehler
V
BAT
V
MOT
24V
24V ext.
Ursache und Lösung
Fehler der Leiterplatte CPU,
LP austauschen
Fehler der Leiterplatte CPU,
LP austauschen
Fehler der Leiterplatte CPU,
LP austauschen
Fehler der Bedienfeld-Anzeige
LCD austauschen
Fehler der Leiterplatte CPU,
LP austauschen
Fehler der Leiterplatte CPU,
LP austauschen
Spannung der Batterie auf LP
PU zu niedrig; LP CPU tauschen
Motorspannung zu niedrig;
Motor-spannung an Messpunkt
(siehe Seite D-2) prüfen,
wenn Spannung an Messpunkt zu
niedrig --> Netzteil tauschen
wenn Spannung an Messpunkt
korrekt --> LP CPU austauschen
24V zu niedrig; Spannung an
Messpunkt P24
(siehe Seite D-2) prüfen,
wenn Spannung an Messpunkt zu
niedrig --> Netzteil tauschen
wenn Spannung an Messpunkt
korrekt --> LP CPU austauschen
24V am Peripherieanschluss zu
niedrig;
Peripheriegerät (z.B. Messer,
Aufwickler, Spendelichtschranke)
abziehen :
wenn Fehler weiter besteht
--> LP CPU austauschen
wenn Fehler nicht mehr besteht
--> Defekt am Peripheriegerät
6.3
Permanent angezeigte Hardware-
fehler
6.3
Permananently displayed Hardware
Errors
Error
ADC malfunction
dRAM malfunction
FPGA malfunction
Invalid setup
LCD malfunction
ROM malfunction
Voltage error
V
BAT
V
MOT
24V
24V ext.
Cause and Solution
Error of CPU PCB;
replace PCB
Error of CPU PCB;
replace PCB
Error of CPU PCB;
replace PCB
Error of CPU PCB;
replace PCB
Error in the LCD module; replace
LCD module
Error of CPU PCB;
replace PCB
Battery voltage on CPU PCB too
low; replace CPU PCB
Motor voltage too low;
Check voltage at measuring point
(see page D-2),
if voltage is too low
--> replace power unit
if voltage is okay
--> replace CPU PCB
24V too low; check voltage at
measuring point P24
(see page D-2)
if voltage is too low
--> replace power unit
if voltage is okay
--> replace CPU PCB
24V at the peripheral connector too
low;
remove peripheral device (f.e. cutter,
rewinder, presence Sensor)
if the error still occurs
--> replace CPU PCB
if the error disappears
--> peripheral device defective
Содержание A4
