C-Com IPAM-1600s Series Скачать руководство пользователя страница 18

Страница: 18 / 148

Introduction

UM1600-2-A 2002

Fig 1-2 displays the LED identification of IPAM-1600s, and Table-1 describes its
color definition and status description.

Fig 1-2 IPAM-1600s LED Identification

Table 1-1 IPAM-1600s LED Description

<LED ID>

Color

Description

POWER

Green

Lit when power on

MAINT

Yellow

Lit when maintance commands were issued

ALARM

Red

Lit when MJ/MN events happen

FAULT

Red

Lit when system error is detected

UP-LNK

Green

Lit when Uplink Ethernet interface was connected

UP-ACT

Green

Blink when information is transmitted through uplink
Ethernet interface Novemebr

ID-2

Yellow

Only applicable for

ID-0 & ID-1

Yellow

ID0, ID1 : off, off ------ ID not assigned
ID0, ID1 : on, off ------ ID = 1
ID0, ID1 : off, on ------ ID = 2
ID0, ID1 : on, on ------ ID = 3

＊

ID = 2 & ID = 3 will not work in IPAM-1600s

ADSL1 –
ADSL16

R/Y/G

Lit Red when no carrier is detected in the specified
ADSL link ;
Lit Green when ADSL link is in active state;
Lit Yellow when the specified ADSL link is in
connection training state;
LED off when ADSL link is not in service

Note:

Do not power off your IPAM-1600s when LEDs “MAINT”, “ALARM” and

“FAULT” are blinking simultaneously because the system is saving
configuration and updating firmware.

Содержание IPAM-1600s Series





















































































































































Результаты поиска

Содержание IPAM-1600s Series

Отзывы:

C-Com IPAM-1600s Series, Руководство пользователя, Страница: 18 / 148

Результаты поиска

Содержание IPAM-1600s Series

Отзывы: