background image

15

Small columns C.BY

PHOT C

PHOT

Photocells on small column

The article C.BY is available as an optional accessory, a pair 
of small columns measuring 50 cm. for the installation of two 
additional photocells P.BY. They must be positioned inside the 
property to protect the movement area of the leaves.
Two distinct connections are envisioned in the control unit that 
are to be used according to the position of the photocell:
PHOT C: The photocell is only active in the closure phase. 
PHOT: The photocell is active in opening and closure.
This functioning mode allows the vehicle to enter even if the 
leaf is not completely open, as long as the manoeuvre area is 
free from obstacles. 

C.BY

Description

Radio transmitter for the long distance commands for BYOU 
automations. 

Functioning

The transmitter has three buttons through which it is possible to 
command the various functions of the automation, configurable 
in the control unit.

Replacing the battery
When the signal LED starts to flash it means that the battery 
is starting to go flat and must be replaced.

Use a small screwdriver as a lever in the zone indicated, in a 
way to open the transmitter.
Replace the new battery by inserting it with the positive pole 
upwards, as indicated in the figure.

IMPORTANT: Do not touch the batteries. 
                         Use rubber gloves.

Transmitter BY

The batteries contain pollutants, do not throw them in 
the normal waste but dispose of the as special waste 
according to the Standards in force.

Close the transmitter.

TECHNICAL DATA

Transmitter BY

Code

Rolling-code

Frequency

433,92 MHz

Functioning temperature

-20°C / +70°C

Dimensions

68x33x16 (mm)

Содержание BEAUTY





























Отзывы: