background image

 

 

 

burster Italia s.r.l. · Sede legale ed operativa · Via Cesare Battisti, 16/18 · 24035 Curno (BG) · Tel. +39 035 618120 · Fax +39 035 618250 

e-mail: [email protected] · http://www.burster.it 

C.F. e P.IVA 11048400151 · Capitale sociale Euro 49.920,00 · R.E.A. di Bergamo 276749 

 
 

 

 
 
 
 

Apparecchi di misura di precisione. Sensori e Sistemi 

per grandezze elettriche, termiche e meccaniche 

11.1  Proprietary Calibration 

Acquisition  of  measurement  points  and  issue  of  a  calibration  protocol  Traceable  calibrated  measuring 
equipment is being used for the calibration. The sensor data are being checked during this calibration. 

11.2  DKD-Calibration 

The  calibration  of  the  sensor  is  carried  out  according  to  the  guidelines  of  the  DKD  and/or  DAkkS..  The 
surveillance of the calibrating-laboratory takes place by the DAkkS. At this calibration, the uncertainty of 
measurement  of  the  torque  measuring  instrument  is  determined.  Further  information  can  be  obtained 
from burster. 

11.3  Re-Calibration 

The recalibration of the torque sensor should be carried out after 26 months at the latest. 
Shorter intervals are appropriate: 

 

Overload of the sensor 

 

After repair 

 

After inappropriate handling 

 

Demand of high-quality standards 

 

Special traceability requirements  

12 

Data Sheet 

See 

www.burster.it 

 

Содержание 86-2800


















Отзывы: