Buderus Logano G315 Скачать руководство пользователя страница 16

Страница: 16 / 56

Boiler block assembly

Logano G315 – 6 720 817 939 (2017/02)

Fig. 18 Boiler assembly tool on rear section

▶ Place both ratchet wrenches onto clamping nuts of the compression

unit and press boiler sections together by tightening evenly.

▶ Release and remove the boiler assembly tool.
▶ Check nipples are seated correctly.

▶ The boiler sections must be aligned to make the installation easier.
▶ Assemble all other boiler sections as described. The front section is

always fitted last.

▶ After the front section is attached, loosen – the assembly tool but do

not remove it.

▶ Insert the tie rod before removing the assembly tool!
▶ Insert the three tie rods (with spring packs fitted) into the cast lugs at

the designated positions (Fig. 19 [1, 2, and 3]). When inserting the
tie rods, make sure the spring packs are mounted on the rear of the
boiler.

▶ Put a nut onto each of the threaded tie rods and tighten by hand.

▶ Now tighten the nuts on the tie rods 1 to 1½ turns.
▶ Level the boiler block vertically and horizontally on the base/

foundation (



Chapter 6.3, page 12).

▶ Remove boiler assembly tool.

Fig. 19 Fitting the tie rods

▶ The next step describes the installation of the supply pipe

(



Chapter 7.4, page 17).

7.3

Setting up the boiler block (assembled block)

▶ Cut the retaining band (Fig. 20, [1]).
▶ Remove the pallet prior to positioning the boiler block (Fig. 20, [2]).

Fig. 20 Boiler block on pallet

▶ Level the boiler block vertically and horizontally on the base/

foundation (



Chapter 6.3, page 12).

The following pages describe the installation of the supply pipe and
sensor well. You must do both irrespective of whether the boiler is
supplied pre-assembled or in separate sections.

NOTICE:

▶ Never compress more than one nipple connection

(two sections) per pressing operation since
otherwise the boiler block could compress unevenly.
This causes leaks in the nipple connections.

NOTICE:

▶ If the boiler packing grooves hit each other,

immediately stop any compression. Additional
compression could damage the boiler sections.

NOTICE:

Damage to system through excessively low

contact pressure.
▶ Do not compress the spring pack. Only use the spring

pack in its original state.

6 720 642 621-13.1o

DANGER: Risk of fatal injury

from falling objects.

▶ Provide a suitable means of supporting the load.
▶ Observe all locally applicable occupational health &

safety regulations regarding lifting equipment.

6 720 642 621-14.1o

6 720 642 621-15.1o

Содержание Logano G315

























































Результаты поиска

Содержание Logano G315

Отзывы:

Похожие инструкции для Logano G315

Бренды по названию

Популярные бренды

Buderus Logano G315, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano G315

Отзывы:

Похожие инструкции для Logano G315

Бренды по названию

Популярные бренды